Multitech Modem Module MT3334SMI Developer'S Manual Download Page 8

Page: 8 / 74

ModemModule Developer’s Guide

MT3334SMI

Carrier Frequencies

Transmit originate:

390 Hz mark

ITU-T V.23

450 Hz space

(1200 bps)

Receive originate:

1300 Hz mark
2100 Hz space

Transmit answer:

1300 Hz mark
2100 Hz space

Receive answer:

390 Hz mark
450 Hz space

Carrier Frequencies

Transmit originate:

980 Hz mark

ITU-T V.21

1180 Hz space

(0–300 bps)

Receive originate:

1650 Hz mark
1850 Hz space

Transmit answer:

1650 Hz mark
1850 Hz space

Receive answer:

980 Hz mark

1180 Hz space

Carrier Frequencies

Transmit originate:

1270 Hz mark

Bell 103/113

1070 Hz space

(0–300 bps)

Receive originate:

2225 Hz mark
2025 Hz space

Transmit answer:

2225 Hz mark
2025 Hz space

Receive answer:

1270 Hz mark
1070 Hz space

Fax Carrier

V.21 Ch2 (half duplex):

Frequencies

1650 Hz mark, 1850 HZ space for transmit originate
1650 HZ mark, 1850 Hz space for transmit answer
V.27ter: 1800 Hz originate/answer
V.29 QAM: 1800 Hz originate/answer
V.17 TCM: 1800 Hz originate/answer

Transmit Level

-11 dBm (dial-up)

Frequency Stability

±0.01%

Receiver Sensitivity

-43 dBm under worst-case conditions

AGC Dynamic Range

43 dB

Interface

Serial interface for EIA RS-232C/ITU-T V.24/V.28

Diagnostics

Local analog loop, local digital loop, remote digital loop.

Weight

0.02 Kg. (0.04 lb.)

Dimensions:

1.045" × 2.541" × 0.680"
(2.7 x 6.5 x 1.8 cm)

Power consumption:

Typical: 215 mA (1.3 W @ 5v DC)
Maximum: 420 mA (2.1 W @ 5.25v DC)

Environmental:

0-50° C; humidity range 20–90% (non-condensing)

Approvals*:

UL 1950 approved
FCC Part 68 approved
Industry canada CS0s
EN60950

* Approvals are provided in controlled configurations and must be re-evaluated in end-user configurations.

Summary of Contents for Modem Module MT3334SMI











































































Search results

Summary of Contents for Modem Module MT3334SMI

Reviews:

Related manuals for Modem Module MT3334SMI

Brands by name

Popular brands

Multitech Modem Module MT3334SMI, Developer'S Manual

Search results

Summary of Contents for Modem Module MT3334SMI

Reviews:

Related manuals for Modem Module MT3334SMI

Brands by name

Popular brands