manualshive.com logo in svg

MULTIQUIP WhisperWatt DCA300SSC, Operation And Parts Manual

Share
Download
MULTIQUIP WhisperWatt DCA300SSC Operation And Parts Manual Download Page 52

page 52 — DCa300SSC / DCa300SSCU gen. • operation anD partS manUal — rev. #1 (08/10/11) 

trOUbLeshOOting (DiagnOstic LaMp)

The engine controller of this generator diagnoses problems 

that arise from the engine control system and the engine 

itself.  Press  the  diagnostic  button  (Figure  66)  on  the 

diagnostic panel to determine if an engine malfunction has 

occurred.

Figure 66. Diagnostic Panel

metHoD oF operation

1.  Normally, the diagnostic lamp will be 

dimly

 lit when 

the 

mpeC Control Switch

 is placed in the 

manUal 

position.

2.  If engine trouble occurs, the diagnostic lamp will be 

brightly

 lit as long as the control switch is left in the 

manual position.

3.  The  diagnostic  lamp  will  indicate  that  an  engine 

malfunction has occurred.

NOTICE

For  a  complete  understanding  of  error  codes  and 

troubleshooting  procedures,  refer  to  the  enclosed 

engine instruction manual

NOTICE

If  the  engine  is  cranked  while  the  diagnostic  switch 

is in the “ON” position, the engine will not be stopped 

even if the starter switch is turned to the “OFF” position. 

In such case, turn the diagnostic switch to the “OFF” 

position..

Summary of Contents for WhisperWatt DCA300SSC









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands