background image

PAGE 28 — WBH-16 SERIES POWER BUGGY • OPERATION AND PARTS MANUAL — REV. #2 (09/12/19)

MAINTENANCE

When performing any maintenance on the power buggy 

or engine, follow all safety messages and rules for safe 

operation stated at the beginning of this manual.

 WARNING

Accidental starts can cause severe injury or 

death. 

ALWAYS

 place the ON/OFF switch in the 

OFF position.

Disconnect and ground spark plug leads 

and disconnect negative battery cable 

from battery before servicing.

 WARNING

Some maintenance operations may 

require the engine to be run. Ensure 

that the maintenance area is well 

ventilated. Exhaust contains poisonous 

carbon monoxide gas that can cause 

unconsciousness and may result in 

DEATH

  CAUTION

ALWAYS 

allow the engine to cool 

before servicing. 

NEVER

 attempt any 

maintenance work on a hot engine.

 CAUTION

Operating the engine with a blocked grass screen, dirty or 

plugged cooling fins, and/or cooling shrouds removed will 

cause engine damage due to overheating.

  DANGER

DO NOT

 use gasoline as a cleaning solvent to avoid 

creating the risk of fire or an explosion.

ENGINE AIR CLEANER

1.  Remove wing nut that secures the air cleaner cover 

to the air cleaner body. Remove cover and set aside.

2.  Next, remove the foam and paper filter elements as 

shown inFigure 29.

3.  Tap the paper filter element (Figure 29) several times 

on a hard surface to remove dirt, or blow compressed 

air [not exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] 

through the filter element from the air cleaner case 

side. 

NEVER

 brush off dirt. Brushing will force dirt 

into the fibers. Replace the paper filter element if it is 

excessively dirty.

Figure 29. Cleaning Paper Filter

 NOTICE

Operating the engine with loose or damaged air cleaner 

components could allow unfiltered air into the engine 

causing premature wear and failure.

  CAUTION

Wear protective equipment such as 

approved safety glasses or face shields 

and dust masks or respirators when 

cleaning air filters with compressed air.

AIR CLEANER

COVER

PAPER FILTER

ELEMENT

BLOW COMPRESSED

AIR FROM THE

INSIDE OUT

FOAM FILTER

ELEMENT

GASKET

WING NUT

Go to Discount-Equipment.com 

to order your parts

Summary of Contents for WBH-16EF CE



















































































Reviews: