![background image](http://html1.mh-extra.com/html/multiquip/qp-2th/qp-2th_operation-and-parts-manual_1855396024.webp)
PAGE 24 — QP3TH TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #9 (02/20/18)
ENGINE AIR CLEANER
1. Remove the air cleaner cover and foam filter element
as shown in Figure 22.
2. Tap the paper filter element (See Figure 22)
several times on a hard surface to remove dirt, or
blow compressed air [not exceeding 30 psi (207 kPa,
2.1 kgf/cm
2
)] through the filter element from the air
cleaner case side.
NEVER
brush off dirt. Brushing
will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
3. Clean foam element in warm, soapy water or
non-flammable solvent. Rinse and dry thoroughly. Dip
the element in clean engine oil and completely squeeze
out the excess oil from the element before installing.
Figure 22. Engine Air Cleaner
DANGER
DO NOT
use gasoline as a cleaning
solvent, because that would create a risk
of fire or explosion.
AIR CLEANER
COVER
PAPER FILTER
ELEMENT
BLOW COMPRESSED
AIR FROM THE
INSIDE OUT
FOAM FILTER
ELEMENT
GASKET
WING NUT
DAILY
1. Thoroughly remove dirt and oil from the engine and
control area. Clean or replace the air cleaner elements
as necessary. Check and retighten all fasteners as
necessary. Check the spring box and bellows for oil
leaks. Repair or replace as needed.
WEEKLY
1. Remove the fuel filter cap and clean the inside of the
fuel tank.
2. Remove or clean the filter at the bottom of the tank.
3. Remove and clean the spark plug (See Figure
20), then adjust the spark gap to 0.028~0.031 inch
(0.6~0.7 mm). This unit has electronic ignition, which
requires no adjustments.
Figure 20. Spark Plug Gap
ENGINE OIL
1. Drain the engine oil when the oil is
warm
as shown
in Figure 21.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 5. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT
over fill.
4. Install drain bolt with sealing washer and tighten
securely.
Figure 21. Engine Oil (Draining)
GAP
:
0.028 – 0.031 in.
(0.7 – 0.8 mm)
DRAIN
BOLT
SEALING
WASHER
OIL FILLER
DIPSTICK
MAINTENANCE (ENGINE)
Summary of Contents for QP-2TH
