background image

PAGE 34 — EM-70 PLASTER/MORTAR MIXER — OPERATION MANUAL — REV. #1 (008/10/04)

EM-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)

Figure 36.  Axle Support  Components

Suspension

The rigid type axle and associated hardware (Figure 35) should
be periodically inspected for signs of excessive wear, elon-
gation of bolt holes, and loosening of fasteners.  Replace all
damaged parts  immediately.

Mixer Cleaning

1.

ALWAYS

 

disconnect the spark plug wire 

(gasoline

engines) before cleaning the inside of the drum. If mixer
is equipped with an electric motor 

remove power cord

from AC  power receptacle

. In addition make sure the

clutch engagement lever is 

dis-engaged

.

2.

Make sure the rear section of the safety grate is
connected to the mixing drum.

3.

At the end of each day’s operation, place mixer drum
in an upright position and spray inside of tub
immediately with water  to prevent lumps of dried mortar
or plaster from forming and contamination of future
batches, 

DO NOT

 allow a buildup of materials to form

on the blades or anywhere inside the drum.

4.

Rotate mixer to dump position and remove debris.

5.

Thoroughly clean

 the entire mixer, wheels, cabinet

and frame.

6.

NEVER!

 pour or spray water over the engine or electric

motor (Figure 37).

7.

When cleaning of the entire mixer is done, return mixing
drum to an upright position.

Mixer Storage

For storage of the mixer for over 30 days, the following is
recommended:

z

Drain the fuel tank completely, or add STA-BIL to the
fuel.

z

Run the engine until the fuel is completely consumed

.

z

Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.

z

Clean the entire mixer and engine compartment.

z

Place the mixing drum in the down position (mouth facing
downward).

z

Cover the mixer and place it a clean dry area, that is
protected from harsh elements.

Figure 38.  Safety Grate (Crush Hazard)

Figure 37.  No Spraying of Water

When rotating the mixing drum from the dump position
to the upright position,

 keep hands clear of safety grate.

The possibility exists of hands or fingers being crushed
(Figure 38).

WARNING

WARNING

WARNING

WARNING

WARNING

Keep Hands

Clear of Drum!

Summary of Contents for EM-70P









































Reviews: