background image

8

When operating the model, all warning and safety information in 
the operating instructions must be observed. 

The model is NOT A TOY in the conventional sense. If you use your model 
carefully, it will provide you and your spectators with lots of fun without 
posing any danger. If you do not operate your model responsibly, this may 
lead to significant property damage and severe injury. You and you alone 
are responsible for following the operating instructions and for ensuring 
the safety guidelines are adhered to.

When setting up the model, operators declare they are familiar with 
and understand the contents of the operating instructions, particularly 
regarding safety information, maintenance work, operating restrictions, 
and deficiencies.

This model may not be operated by children under the age of 14. If minors 
operate the model under the supervision of a responsible and competent 
adult pursuant to the law, this person is responsible for adhering to the 
information in the operating instructions.

THE MODEL AND THE ASSOCIATED ACCESSORIES MUST BE KEPT OUT 
OF REACH OF CHILDREN UNDER 3 YEARS OF AGE! CHILDREN UNDER 3 
COULD SWALLOW REMOVABLE SMALL PARTS OF THE MODEL. RISK OF 
SUFFOCATION!

Multiplex Modellsport GmbH & Co. KG is not liable for loss, damage 
and consequential damage of any kind caused by incorrect operation, 
improper use or misuse of this product, including the accessories used 
along with it.

Proper use

The model may only be used in the hobby sector. No other type of use 
is permitted. To operate the model, only the accessories recommended 
by Multiplex may be used. The recommended components have been 
tested and adjusted for safe functioning together with the model. If other 
components are used or the model is modified, all claims against the 
manufacturer or retailer are void.

In order to minimize the risk when operating the model, observe the 
following points in particular:

•  The model is controlled via a remote control. No remote control is 

safe from radio interference. Interference may lead to a loss of control 
of the model. Therefore, always ensure large safety distances in all 
directions when operating the model. As soon as even the smallest 
indication of radio interference presents itself, operation of the model 
must be halted immediately!

•  The model may only be put into operation after a complete function 

and range test has been successfully carried out as per the instruc-
tions for the remote control.

•  The model may only be flown in good visibility. Do not fly in poor light 

or in the direction of the sun in order to avoid glare.

•  The model may not be operated under the influence of alcohol or other 

intoxicants. The same applies for medicines that impair perception and 
responsiveness.

•  Only fly the model in wind and weather conditions in which you can 

safely control it. Even with light wind, take into account that turbulence 
may build up on objects and have an effect on the model.

•  Never fly in places where this would pose a danger to others, i.e. in 

residential areas, near power lines, roads, and railroad tracks.

•  Never direct the model at people or animals! Avoid unnecessary risks 

and alert other pilots to potential hazards. Always fly in a manner that 
ensures neither you nor others are exposed to danger – even many 
years of accident-free flying experience are no guarantee for the next 
minute of flying time.

Residual risks

Even if the model is operated in accordance with the regulations and 
observing all safety aspects, there is always a residual risk. 

Third-party liability insurance (powered model airplane) is therefore 
mandatory. If you are a member of a group or association, you might be 
able to take out the appropriate insurance there. 

Ensure models and the remote control are properly maintained and are in 
good condition at all times.

Due to the construction and design of the model, the following dangers 
may arise in particular:

Injuries caused by the propeller: As soon as the battery is connected, the 
area around the propeller must be kept clear. Be aware that objects in 
front of the propeller may be sucked in and objects behind the propeller 
may be blown away. Always align the model ensuring it cannot move in 
the direction of other people if the motor starts up unintentionally. When 
performing adjustments for which the motor is running or may start up, 
the model must always be securely held in place by a helper.
•  Crashes caused by control errors: Even the most experienced pilots 

can make mistakes. For this reason, only fly in a safe environment and 
at authorized model airplane flying fields.

•  Crashes caused by technical failures, undetected damage from 

transportation or pre-existing damage: The model must be carefully 
inspected before each flight. Bear in mind that technical or material 
failures may occur at any time. Therefore, only operate the model in a 
safe environment.

•  Adhere to operating limits: Excessively harsh flying weakens the struc-

ture of the model and may lead to technical and material failures as 
well as crashes immediately or, due to 'insidious' consequential dam-
age, in later flights.

•  Risk of fire due to malfunction of the electronics: Batteries must be 

stored safely. The safety information of the electronic components in 
the model, the battery, and the charging device must be observed. 
The electronics must be protected from water. The controller and the 

Safety information for MULTIPLEX airplane models

EN

Summary of Contents for 4059818021147





































Reviews: