background image

 

 

 

 

Chapter 1 – SocketModem

®

 

Cell (MTSMC-

G2) & SocketModem

®

 

iCell (

MTSMC-G2-IP)

 

 

Introduction 

The MTSMC-G2 is a serial to wireless quad-band GPRS SocketModem. It is a complete, ready-to-integrate SocketModem 
that offers standards-based multi-band GSM/GPRS Class 10 performance. It is based on industry-standard open interfaces 
and utilizes Multi-Tech’s universal socket design. The SocketModem is available with the Multi-Tech's 

Universal IP

™ stack to 

bring embedded Internet connectivity to any device.  

Notes about Activation:

  

 

These units are shipped without network activation. 

 

 

To connect to the wireless network, you will have to establish a wireless account. See the Wireless Activation 
procedures on separate sheets included with the Developer Kit and available on the Developer Kit CD. 

Product Build Options and Ordering Information 

Product 

Description 

Region 

Order This 

Product 

3

 

MTSMC-G2 

Quad-band GPRS SocketModem Cell  

US Default 

 

MTSMC-G2-ED 

Quad-band GPRS SocketModem Cell  

EU Default 

 

MTSMC-G2-V 

Quad-band GPRS SocketModem Cell with Voice  

US Default 

 

MTSMC-G2-V-ED 

Quad-band GPRS SocketModem Cell with Voice  

EU Default 

 

MTSMC-G2-IP 

Quad-band GPRS SocketModem iCell with Universal IP  

US Default 

 

MTSMC-G2-IP-ED 

Quad-band GPRS SocketModem iCell with Universal IP  

EU Default 

 

Developer Kit 

MTSMI-UDK 

Universal Developer Kit 

Global 

 

 

How to Read the Product Codes in the Table Above: 

G2 GPRS 

ED European 

Default 

Voice (microphone and speaker) 

IP 

Universal IP™ Stack  

UDK Universal 

Developer 

Kit 

 

Other Product Codes: 

The complete product code may end in 

.Rx

. For example, MTSMC-G2.Rx.   

“R” indicates product revision. “

x

” is the revision number. 

Note:

 All products can be ordered in single packs or 50-packs. Single pack product codes end in 

SP

 

AT Commands Reference Guides

 

Products 

AT Commands Reference Guide Title & Document Number  Fax Commands Voice Commands 

SocketModem Cell 
(MTSMC-G2 and 
MTSMC-G2-V ) 

GPRS AT Commands for Multi-Tech G2 Wireless Modems 

(S000463x)

 

AT Commands for Multi-Tech G2 Wireless Modems with IP 
Connectivity 

(S000469x)

 

NA Included 

 

SocketModem iCell 
(MTSMC-G2-IP) 

GPRS AT Commands for Multi-Tech G2 Wireless Modems 

(S000463x)

 

Universal IP Commands 

(S000457x)

 

NA Included 

 

Summary of Contents for MTSMC-G2


































Reviews: