Multi-Amp CB-832 Instruction Manual Download Page 28

 

 

Part 

 12470 

 

Rev. 2  3/25/99 

25 

7. 

Power on, instrument displays lighted, either or both instruments will not function 

when unit is initiated: 

 

a. 

Failure in 15VDC  power supply circuitry. 

b. 

Failure of protective diodes in current input or display section of ammeter. 

 

NOTE:

 

Refer to other example conditions before assuming these failures. 

 

WARRANTY

 

 

Multi-Amp Corporation warrants to the original purchaser that the product is free of defects in 

material and workmanship for a period of one (1) year from date of shipment.  This warranty is 

limited and shall not apply to equipment which has damage, or cause of defect, due to accident, 

negligence, improper operation, faulty installation by the purchaser, or improper service or repair by 

any person, company or corporation not authorized by Multi-Amp Corporation. 

 

Multi-Amp Corporation will, at its option, either repair or replace those parts and/or materials that it 

deems to be defective.  Any costs incurred by the purchaser for the repair or replacement of such 

parts and/or materials shall be the sole responsibility of the original purchaser. 

 

THE  ABOVE  WARRANTY  IS  IN  LIEU  OF  ALL  OTHER  WARRANTIES,  EITHER 

EXPRESSED OR IMPLIED ON THE PART OF THE MULTI-AMP CORPORATION, AND 

IN  NO  EVENT  SHALL  THE  MULTI-AMP  CORPORATION  BE  LIABLE  FOR  THE 

CONSEQUENTIAL DAMAGES DUE TO THE BREACH THEREOF.

 

Summary of Contents for CB-832






























Reviews: