Muller Elektronik MAXI 3.0 Operating Instructions Manual Download Page 16

Page: 16 / 90

About the job computer

System Overview

V1.20180921

30303187-02-EN

ISOBUS SPRAYER-Controller MAXI 3.0 job
computer

Junction box C

Connector cable for job computer to ISOBUS
Connection to ISOBUS power socket

Junction box B

Water and dust protection cap.
Otherwise, connection of extensions.

Junction box A

Main system - MIDI

The system can be expanded. The basic version consists of one to three job computers. The first job
computer is connected to the ISOBUS power socket on the tractor.

Main system of the MIDI 3.0 version

Connector cable for job computer to ISOBUS
Connection to ISOBUS power socket

ECU-MIDI - Master

Connector cable

ECU-MIDI - Slave

Termination plug
Otherwise, connection of extensions.

ECU-MIDI - Slave

3.2.2

Summary of Contents for MAXI 3.0



























































































Search results

Summary of Contents for MAXI 3.0

Reviews:

Related manuals for MAXI 3.0

Brands by name

Popular brands

Muller Elektronik MAXI 3.0, Operating Instructions Manual

Search results

Summary of Contents for MAXI 3.0

Reviews:

Related manuals for MAXI 3.0

Brands by name

Popular brands