background image

Customer Service Center

Decatur, Illinois

800.798.3131

www.muellergas.com

[email protected]

All warranties, expressed or implied, for Mueller Drilling Machines are 

rendered null and void if the machines are used with shell cutters or 

equipment manufactured by someone other than Mueller Co.

      WARNING:

 

1. Read and follow instructions carefully. Proper training and periodic 

review regarding the use of this equipment is essential to prevent possible 

serious injury and/or property damage. The instructions contained 

herein  were  developed  for  using  this  equipment  on  fittings  of  Mueller 

manufacturer only, and may not be applicable for any other use.

2. Do noT exceed the pressure ratings of any components or equipment. 

Exceeding the rated pressure may result in serious injury and/or property 

damage.

3. Safety goggles and other appropriate protective gear should be used. 

Failure to do so could result in serious injury.

4. Pressure test, check for and repair leaks in all fittings and components 

each time one is installed or any joint or connection is broken. Failure 

to  find  and  repair  a  leak  from  any  source  in  the  fittings,  by-pass  lines 

or equipment could result in an explosion and subsequent serious injury 

and/or property damage.

5. MUELLER

®

 Drilling Machines and Equipment have been carefully 

designed and engineered to work together as a unit. The use of equipment 

manufactured by someone other than Mueller Co. may cause excessive 

wear or a malfunction of the MUELLER machines.

!

Reliable Connections

TM

C1-36

Drilling

Machine

 

MUELLER

®

GAS 

o p E R At i n G   i n S t R U c t i o n S   M A n U A L

 

TAbLE oF ConTEnTS   PAGE

 

General Information 

2

 

Maintenance Instructions 

3

 

Operating Instructions 

4-6

 

Travel Charts 

7-10

 

Installation Instructions: 

 

Replacing Feed Knob

 

with Auto-Feed Lever 

11

Summary of Contents for C1-36













Reviews: