MTX X3-17-SW-D Owner'S Manual Download Page 2

M T X . C O M

2

THANK YOU

Thank you for making the AWESOME decision to purchase our MTX Audio direct-fit subwoofer 

enclosure designed for the Can-Am

®

 Maverick X3. Our sub enclosure, with its 3512-04S 12" shallow 

subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in 

any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time. 

So, what are you waiting for? It’s time to get the rumble in your ride and go hit the trails! Oh, and 

congratulations on your purchase, thanks for your support and most importantly, enjoy the ultimate 

audio experience with MTX!

WE’RE HERE TO HELP

We’re here to help with any installation or technical support. Visit mtx.com to chat, call  

1-800-225-5689 to speak with an MTX Technical Support representative, or visit 

youtube.com/user/MTXAudioUSA to view product videos. 

DON’T FORGET TO REGISTER YOUR PRODUCT

Don’t forget to register your new MTX Audio product. Visit mtx.com/productregistration or scan the 

QR code to the right.

Model #

Serial #

Dealer’s Name

Date of Purchase

IMPORTANT NOTICE

Whenever working on the vehicle, it is recommended to disconnect the battery prior to starting work. 

Failure to do so may lead to a risk of electric shock or equipment damage.

When connecting power and ground wires ensure that the red power wire is fused at the point 

where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a 

short circuit develops between the vehicle connection point and the product.

Summary of Contents for X3-17-SW-D













Reviews: