MTX MTX-3G-JAVA-IoT Hardware User'S Manual Download Page 51

Page: 51 / 128

MTX-Java-IoT | 2018/2

MTX © by MATRIX ELECTRONICA S.L.U.

SUPPORT:

[email protected] |

SALES:

[email protected] |

mtxm2m.com

2. Operating Temperatures

Please note that the modem’s lifetime, i.e., the MTTF (mean time to failure) may be reduced if operated

outside the extended temperature range.

PARAMETER

MIN

TYP

MAX

UNIT

Normal operation

-30

ºC

Extended operation

-40

ºC

Automatic shutdown

<-40

>90

ºC

1. Extended operation allows normal mode speech calls or data transmissions for a limited time

until the automatic thermal shutdown mode takes effect. Within the extended temperature

range (outside the operating temperature range) the specified electrical characteristics may

be increased or decreased.

2. Due to uncertainty in temperature measurement, a tolerance of ±3ºC on the stated shutdown

thresholds may occur.

Note that within the specified operating temperature ranges the unit temperature may vary to a great

extent depending on the operating mode, used frequency band, radio output power and current supply

voltage.

Summary of Contents for MTX-3G-JAVA-IoT

































































































































Search results

Summary of Contents for MTX-3G-JAVA-IoT

Reviews:

Related manuals for MTX-3G-JAVA-IoT

Brands by name

Popular brands

MTX MTX-3G-JAVA-IoT, Hardware User'S Manual

Search results

Summary of Contents for MTX-3G-JAVA-IoT

Reviews:

Related manuals for MTX-3G-JAVA-IoT

Brands by name

Popular brands