manualshive.com logo in svg

MTU 12V2000Gx6 series, Operating Instructions Manual

The MTU 12V2000Gx6 series is a high-performance engine designed for industrial applications. To ensure optimum operation, it is essential to have the Operating Instructions Manual on hand. You can easily download this manual free of charge from our website, enabling you to maximize the performance of your product.

Share
Download
background image

4.

Open threaded vent plug (1) of filter to be
serviced.

5.

Open drain plug (1).

6.

Allow water to drain until fuel emerges.

7.

Close drain plug (2) again.

8.

Drain second filter on module, from
(→ Step 4).

9.

Close threaded vent plug again.

10.

Open fuel supply.

11.

Vent fuel prefilter (→ Page 155).

Draining fuel prefilter with high
pressure, version B

Note:

The fuel prefilter can be drained during
engine operation or with the engine at a
standstill!

1.

Provide a suitable container to collect the wa-
ter.

2.

Take care when opening drain plug (1) be-
cause fuel or water can spurt out.

3.

Allow water to drain until fuel emerges.

4.

Close drain plug (2) again.

144 | Fuel Filter | MS15054/03E 2018-07

TIM-ID: 0000066428 - 005

Summary of Contents for 12V2000Gx6 series
















































































































































































































































Reviews:

No comments

Related manuals for 12V2000Gx6 series

Daspi PASSAGE User Manual preview
PASSAGE
Brand: Daspi Pages: 40
Daewoo POLUS P126TI Operation Manual preview
POLUS P126TI
Brand: Daewoo Pages: 205
ZIEHL-ABEGG ZA top SM210.60 Original Operating Instructions preview
ZA top SM210.60
Brand: ZIEHL-ABEGG Pages: 96
Vacmaster AM201R Operator'S Manual preview
AM201R
Brand: Vacmaster Pages: 12
DUROMAX XP7HPX User Manual preview
XP7HPX
Brand: DUROMAX Pages: 70
Volvo Penta MD22 Workshop Manual preview
MD22
Brand: Volvo Penta Pages: 132
Volvo B 17 Service Manual preview
B 17
Brand: Volvo Pages: 64
Yanmar 3TNV84T-BGGE General Specification preview
3TNV84T-BGGE
Brand: Yanmar Pages: 2
Yanmar 3TNM72-HGE General Specification preview
3TNM72-HGE
Brand: Yanmar Pages: 2
Yanmar 3JH3BE Operation Manual preview
3JH3BE
Brand: Yanmar Pages: 48
DANA 4360-48 Parts List preview
4360-48
Brand: DANA Pages: 3
DANA 4360-37 Parts List preview
4360-37
Brand: DANA Pages: 3
DLE DLE61 User Manual preview
DLE61
Brand: DLE Pages: 4
Asmo Marine Thoosa Installation Manual preview
Thoosa
Brand: Asmo Marine Pages: 8
Stiga WBE Series Operator'S Manual preview
WBE Series
Brand: Stiga Pages: 232
KTM 250 D-XC Manual preview
250 D-XC
Brand: KTM Pages: 11
Neodrives Z20 RS User Manual preview
Z20 RS
Brand: Neodrives Pages: 26
Ford 2722 Service Manual preview
2722
Brand: Ford Pages: 71

Brands by name

Popular brands

Load more brands