background image

RAPIDDOC

™ TABLET KIOSK 

INSTALLATION GUIDE

8

 MTI P/N 063-00180 rev B ©2018 MTI All Rights Reserved

www.armoractive.com.com  |  T:800.426.6844

Federal Communication Commission interference statement

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: -Reorient or relocate the receiving 
antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into 
an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an 
experienced radio/TV technician for help. 

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1.  this device may not cause harmful interference and  
2.  this device must accept any interference received, including interference that may cause undesired 

operation

RF Exposure Warning

The equipment complies with RF exposure limits set forth for an uncontrolled environment. The 
antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible for 
compliance could void your authority to operate the equipment.

FCC Statement

Summary of Contents for RAPIDDOC KIOSK











Reviews: