MTHTrains 263E STEAM ENGINE CONTEMPORARY VERSION Operating Instructions Manual Download | Manualshive

Page: 16 / 36

background image

16

MTH 263e Operating Manual

TINPLA

TE

SELF-RECHARGING BATTERY BACKUP

ProtoSounds® state-of-the-art design includes a self-recharging battery

backup system for improved performance at any speed. The battery ensures
that power to the sound system will remain on during directional changes,
setting RESET options or when travelling over dirty track and switches.
The self-recharging battery backup system is automatically turned on or off
whenever track power is turned on or are off. There no switches needed to
enjoy the benefits of the automatic battery backup system.

ProtoSounds® contains a warning alarm if the battery backup system fails

to automatically disengage when track power is turned off. Should the
backup system fail, you will hear a repeating whistle blast indicating this
has occurred. Should this happen, unplug the battery from the ProtoSound
module (to prevent the battery from being run down) and contact MTH for
instructions on returning the tender for repair.

REPLACING THE PROTOSOUND® BATTERY

The ProtoSound® battery (located in the tender body, is a special NiCad

7-cell, 8.4v battery - NOT the 6-cell, 7.2v battery found in most
convenience stores. The 6-cell NiCad is NOT recommended for use with
ProtoSound® applications. The battery is continually charged from the
track when power is applied and should last for up to five years. In
addition, the NiCad battery is a dry battery and should not leak or cause any
damage to your locomotive during its lifetiem.

If you notice that the sounds seem distorted or garbled at low voltages or

become silent when power from the transformer is shut off, the battery may
be going bad. Before replacing the battery, you should put the engine in
NEUTRAL and leave the transformer throttle set at about 12 volts for 15
minutes. This should temporarily recharge the battery. If the garbled or
distorted sounds are reduced, then your battery charge has worn down. You
can give your battery a full charge by leaving the engine ON in the
NEUTRAL position for 18 hours. (Make sure the smoke unit switch is in
the OFF position to prevent harm to the smoke unit wicking).

If you need to replace the battery, replacement ProtoSound® batteries are

available from MTH ProtoSound Electronics at 7020 Columbia Gateway
Drive, Columbia, MD 21046. A standard 9v alkaline battery can be

«
...
14
15
16
17
18
...
»

Summary of Contents for 263E STEAM ENGINE CONTEMPORARY VERSION





































Reviews:

No comments

Related manuals for 263E STEAM ENGINE CONTEMPORARY VERSION

Brand: RC4WD Pages: 79

25124 CHECKERED FLAG RUN

Brand: Carrera Pages: 24

Brand: GREAT PLANES Pages: 35

Spirit GPMA0530

Brand: GREAT PLANES Pages: 40

Maker ROK Robotics

Brand: Rokenbok Pages: 4

4 Wheel Drive Truck Building Set

Brand: K'Nex Pages: 20

Brand: VQ Pages: 1

Brand: E sky Pages: 32

Leaping Letters

Brand: LeapFrog Pages: 2

Tamagochi Friends

Brand: Bandai Pages: 4

Brand: MAC Rail Pages: 8

Brand: H-KING Pages: 12

Taylorcraft 130

Brand: Ares Pages: 32

Fordhampton Farm House

Brand: GAUGEMASTER Pages: 4

Star Wars Electronic Ask Yoda 72410

Brand: Hasbro Pages: 4

Super Mario Adventures with Peach

Brand: LEGO Pages: 24

Brand: Hot Wheels Pages: 4

Me 262A Schwalbe

Brand: Eduard Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands