MTD VC6X Series Operator'S Manual Download Page 16

Maintenance & Adjustments

6

16

Maintenance

General Recommendations

• 

Always observe safety rules when performing any 

maintenance.

• 

The warranty on this lawn mower does not cover items that 

have been subjected to operator abuse or negligence. To 

receive full value from warranty, operator must maintain 

the lawn mower as instructed here.

• 

Changing of engine-governed speed will void engine 

warranty.

• 

All adjustments should be checked at least once each 

season.

• 

Periodically check all fasteners and make sure these are 

tight.

WARNING: 

Always stop engine, allow engine to 

cool, disconnect spark plug, and ground against 

engine before performing any type of maintenance 

on your machine.

Lubrication

1. 

Lubricate pivot points on the blade control at least once 

a season with light oil. This control must operate freely in 

both directions. See Figure 6-1.

Figure 6-1

2. 

The transmission is pre-lubricated and sealed at the factory 

and does not require lubrication.

3. 

Follow the accompanying engine manual for lubrication 

schedule and instruction for engine lubrication.

Deck Care

Clean underside of the mower deck after each use to prevent 

build-up of grass clippings or other debris. Follow steps below 

for this job.
1. 

Disconnect spark plug wire. Drain gasoline from lawn 

mower or place a piece of plastic under the gas cap.

2. 

Tip mower so that it rests on the housing. Keep the side 

with the air cleaner facing up. Hold mower firmly.

WARNING: 

Never tip the mower more than 90º in 

any direction and do not leave the mower tipped for 

any length of time. Oil can drain into the upper part 

of the engine causing a starting problem.

3. 

Scrape and clean the underside of the deck with a suitable 

tool. 

4. 

Put the mower back on its wheels on the ground. If you had 

put plastic under the gas cap earlier, make sure to remove it 

now.

Summary of Contents for VC6X Series

























Reviews: