MTD VB20 series Operator'S Manual Download Page 7

7

S

ection

 2 — i

mportant

 S

afe

 o

peration

 p

racticeS

WARNING:

 

Your Responsibility—Restrict the use of this power machine to persons who read, understand and 

follow the warnings and instructions in this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that may appear on this product.  Read, understand, and follow all instructions on the 

machine before attempting to assemble and operate.

Symbol

Description

READ THE OPERATOR’S MANUAL(S) 

Read, understand, and follow all instructions in the manual(s) before attempting to 

assemble and operate

DANGER — ROTATING BLADES 

To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover 

or grass catcher is in its proper place. If damaged, replace immediately.

DANGER — BYSTANDERS 

Do not mow when children or others are around.

DANGER — HAND/ FOOT CUT 

Keep hands and feet away from rotating parts.

DANGER — THROWN DEBRIS 

Remove objects that can be thrown by the blade in any direction. Wear safety glasses.

DANGER — SLOPES

Use extra caution on slopes. Do not mow slopes greater than 15

°

.

WARNING—GASOLINE IS FLAMMABLE 

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon 

monoxide, an odorless and deadly gas.

WARNING— HOT SURFACE 

Engine parts, especially the muffler, become extremely hot during operation. Allow engine 

and muffler to cool before touching.

Summary of Contents for VB20 series





























Reviews: