MTD Series 830 Operator'S Manual Download Page 2

2

Finding and Recording Model Number

Table of Contents

BEFORE ASSEMBLING YOUR NEW EQUIPMENT, 
please locate the model plate on the equipment and 
copy the information to the sample model plate pro-
vided to the right. You can locate the model plate by 
standing at the operating position and looking down 
at the rear of the deck. This information will be neces-
sary to use the manufacturer’s web site, to obtain 
assistance from the Customer Support Department, 
or when contacting an authorized service dealer.

This Operator’s Manual is an important part of your new lawn mower. It will help you assemble,  

prepare, and maintain the unit for best performance. Please read and understand what it says. 

Model Number

Serial Number

•  Visit 

www.mtdproducts.com

•  Call a Customer Support Representative at 

1-800-800-7310

.

•  The 

engine manufacturer 

is responsible for all engine-related issues with regards to performance, power-rating, specifica-

tions, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual, packed separately with 
your unit, for more information. 

 

Please do NOT return the unit to the retailer from which it was purchased, without first 

contacting Customer Support.

Customer Support

Slope Gauge........................................................ 3
Safe Operation Practices ................................... 4
Setup and Adjustment ....................................... 6
Operating Your Lawn Mower .............................. 8

Maintaining Your Lawn Mower ......................... 10
Troubleshooting ................................................ 14
Off-Season Storage and Safety Labels .......... 15
Parts List ........................................................... 16

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this 
unit, you can seek help from the experts. Choose from the options below:

MTD LLC reserves the right to change product specifications, designs, and equipment without notice and without incurring obligation.

Summary of Contents for Series 830





















Reviews: