MTD C3X series Operator'S Manual Download | Manualshive

Page: 20 / 28

background image

20

S

ection

8 — t

roubleShooting

Problem

Cause

Remedy

Uneven cut

1. Wheels not positioned correctly.

2. Dull blade.

1. Place front and rear wheels in same height

position. (Dual Height Adjusters)

2. Sharpen or replace blade.

Mower will not self propel

1. Belt not installed properly.

2. Debris clogging drive operation.

3. Damaged or worn belt.

4. Drive control out of adjustment.

1. Check belt for proper pulley installation and

movement.

2. Stop engine, disconnect spark plug boot,

and clean out debris.

3. Inspect and replace belt.

4. Adjust drive control. (See Assembly & Set-up

section).

High pullback effort

1. Pulling mower backwards before

transmission disengages.

1. Allow the unit to roll forward slightly without

the drive lever(s) engaged before pulling

backwards.

«
...
18
19
20
21
22
...
»

Summary of Contents for C3X series





























Reviews:

No comments

Related manuals for C3X series

Brand: H&S Pages: 32

Brand: McCulloch Pages: 36

Brand: Jacobsen Pages: 108

Brand: AL-KO Pages: 116

Brand: Gardenline Pages: 30

532 43 41-99 Rev. 1

Brand: McCulloch Pages: 72

Brand: Toro Pages: 2

Brand: Yard Works Pages: 35

Brand: Ransomes Pages: 92

Brand: Cub Cadet Pages: 44

Silver Series 10270

Brand: Lawn-Boy Pages: 29

Brand: Nakayama Pages: 19

TZ51SF-BS625EXi

Brand: MADER Pages: 67

Brand: Toro Pages: 52

Brand: Qualcast Pages: 29

White Outdoor GT2550

Brand: MTD Pages: 56

Brand: Toro Pages: 24

Brand: KUHN Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands