MTD 462 thru 465 Operator'S Manual Download Page 11

11

An unbalanced blade will cause excessive vibration 
when rotating at high speeds and may cause 
damage to the unit. The blade can be tested by 
balancing it on a screwdriver or nail. Remove metal 
from the heavy side until it is balanced evenly.

When reassembling the blade, tighten center bolt to 
between 550 and 700 in.-labs. and the two out bolts 
to between 250 and 350 in.-labs.     

Storing Your Chipper Shredder

Clean the equipment thoroughly.

Wipe equipment with an oiled rag to prevent rust.

Refer to engine manual for correct engine storage 
instructions

Store unit in a clean, dry area. Do not store next to 
corrosive materials such as fertilizer.

SECTION 6:  TROUBLESHOOTING

NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer. 

Problem

Cause

Remedy

Engine fails to start

1.

Spark plug wire disconnected.

2.

Fuel tank empty or stale fuel.

3.

Throttle control lever not in correct 
starting position. (If Equipped)

4.

Choke not in CHOKE position.
(If Equipped) 

5.

Blocked fuel line.

6.

Faulty spark plug.

1.

Connect wire to spark plug.

2.

Fill tank with clean, fresh gasoline.

3.

Move throttle lever to FAST position.

4.

Move choke to CHOKE position.

5.

Clean fuel line.

6.

Clean, adjust gap, or replace.

Engine runs erratic

1.

Spark plug wire loose.

2.

Unit running on CHOKE.
(If Equipped)

3.

Blocked fuel line or stale fuel.

4.

Water or dirt in fuel system.

5.

Dirty air cleaner.

6.

Carburetor out of adjustment.

1.

Connect and tighten spark plug wire.

2.

Move choke lever to OFF position.

3.

Clean fuel line; fill tank with clean, fresh 
gasoline

4.

Drain fuel tank. Refill with fresh fuel.

5.

Clean or replace air cleaner.

6.

See authorized service dealer.

Too much vibration

1.

Loose parts or damaged impeller.

1.

See authorized service dealer.

Engine overheats

1.

Engine oil level low.

2.

Dirty air cleaner.

3.

Carburetor not adjusted properly.

1.

Fill crankcase with proper oil.

2.

Clean or replace air cleaner.

3.

See authorized service dealer.

Occasional skip (hesitates) 
at high speed

1.

Spark plug gap too close.

1.

Adjust gap to.030”.

Unit does not discharge

1.

Discharge chute clogged.

2.

Foreign object lodged in impeller.

3.

Low engine RPM

4.

Vacuum bag is full.

1.

Stop engine immediately and 
disconnect spark plug wire. Clean flail 
screen and inside of discharge opening.

2.

Stop engine and disconnect spark plug 
wire. Remove lodged object.

3.

Always run engine at full throttle.

4.

Empty bag.

Rate of discharge slows 
considerably or 
composition of discharged 
material changes.

1.

Low engine RPM.

2.

Chipper blade dull.

1.

Always run engine at full throttle.

2.

Replace chipper blade or see your 
authorized service dealer.

Summary of Contents for 462 thru 465

















Reviews: