manualshive.com logo in svg

MTD 074 Series, Operator'S Manual, Page: 12 / 16

Share
Download
MTD 074 Series Operator'S Manual Download Page 12

12

For repairs beyond 

the minor adjustments 

listed here, contact 

an authorized service 

dealer. 

6

Trouble 

Shooting

Cause

Problem

Remedy

Engine fails to start

1.  Blade control disengaged.
2.  Spark plug wire disconnected.
3.  Fuel tank empty or stale fuel.
4.  Engine not primed.

5.  Faulty spark plug.
6.  Blocked fuel line.
7.  Engine flooded.

1.  Engage blade control.
2.  Connect wire to spark plug.
3.  Fill tank with clean, fresh gasoline.
4.  Prime engine as instructed in 

“Operating Your Lawn Mower”.

5.  Clean, adjust gap, or replace.
6.  Clean fuel line.
7.  Wait a few minutes to restart, but 

do not prime.

Engine runs erratic

1.  Connect and tighten spark  

plug wire.

2.  Clean fuel line; fill tank with clean,  

fresh gasoline.

3.  Clear vent.
4.  Drain fuel tank. Refill with  

fresh fuel.

5.  Refer to engine manual.
6.  Refer to engine manual.

1.  Spark plug wire loose. 

2.  Blocked fuel line or stale fuel. 

3.  Vent in gas cap plugged.
4.  Water or dirt in fuel system. 

5.  Dirty air cleaner.
6.  Carburetor out of adjustment.

Engine overheats

1.  Fill crankcase with proper oil.
2.  Remove blower housing  

and clean.

3.  Refer to engine manual.

1.  Engine oil level low.
2.  Air flow restricted. 

3.  Carburetor not adjusted properly.

Occasional skips 

(hesitates) at 

high speed

1.  Adjust gap to .030”.
2.  Refer to engine manual.

1.  Spark plug gap too close.
2.  Carburetor idle mixture adjustment 

improperly set.

Idles poorly

1.  Reset gap to .030” or replace  

spark plug.

2.  Refer to engine manual.
3.  Refer to engine manual.

1.  Spark plug fouled, faulty or gap  

too wide.

2.  Carburetor improperly adjusted.
3.  Dirty air cleaner.

Uneven cut

1.  Place all four wheels in same  

height position.

2.  Sharpen or replace blade.

1.  Wheels not positioned correctly.

2.  Dull blade.

Excessive

Vibration

1.  Cutting blade loose or unbalanced.

2.  Bent cutting blade.

1.  Tighten blade and adapter. 

Balance blade.

2.  See an authorized service dealer.

Summary of Contents for 074 Series

















Reviews:

No comments