-A-
Display of the consumed current in amperes with a step of 0.05 A. This mode is extremely useful for
diagnosing the condition of the engine and machine mechanism.
Charging and accumulator:
Accumulator type:
This machine is designed to work with any 18650 or 18350 lithium battery. The operating time will directly depend
on its capacity.
Display (indication):
When you have installed a fully charged battery and turned on the
machine, the display will show “FUL” in the
charge indication mode, indicating that the machine has identified the battery as fully charged. Further, during the
discharge process, the display will show the current remaining charge in percent.
When the battery charge drops to 20%, the machine, regardless of the display mode you have set, on the display
will start to show a blinking percentage of the remaining charge, which warns you about the need to replace the battery
or connect the charging cord to the connector. The remaining operating time is approximately 1-2 hours, depending on
the voltage set and the load on the machine.
When the battery is fully discharged during operation, the machine will smoothly stop, and when you try to turn
it on, the blinking inscription "LO" will light up on the display, indicating that the battery energy is not enough to start.
Charging
The battery can be charged both from the charging station included in the delivery set, and from the machine
directly, both in the off and on state.
Charging from the station: Install the required amount of batteries in the slots of the station with a negative * (see
above) contact towards you. Connect the wire with the micro USB connector to the station, and the USB Type A connector
to the mains or adapter. You can power the station from any power source without restrictions. The charging time will
directly depend on the current strength of the supply network. The maximum possible current strength is 2A. During
charging, the station indicators above the battery will glow red. When charging is complete, they will turn green.
Charging directly from the machine in the off state: Connect the MT USB Type-A to USB Type-C wire to the machine
with the USB Type-C connector. Connect the USB Type-A connector to a power outlet. There are no restrictions on the
power of the supply network, but charging the battery directly with the machine will be carried out with a current of 0.5A,
which is much slower than the current of the charging station. To indicate the charge, shortly press the "MT" button. A
flashing -P-
will appear on the screen. When charging is complete, the display will show “FUL”. If you need to turn on the
machine while charging, hold down the "MT" button.
Charging directly from the machine when it is turned on: You can plug in the charging cord while you work without
turning off the machine. The display mode will automatically switch to the flashing -P- symbol. It can be switched to any
other mode as desired. This mode is "endless" and the inscription "FUL" indicating a full charge does not turn on in it, since
the machine in this mode constantly consumes energy and cannot be charged at 100%.
Please note that after the battery is completely discharged and the power cord is connected, the battery needs
some time to gain the required power to start. During this time, when you try to turn on the machine, the display will show
a blinking inscription "LO".
If in the process of work you need to simultaneously charge the clipper and the battery in the charging station,
but at the same time use a single USB power supply port or adapter, then you can connect the cord of the clipper directly
to the USB Type A connector of the charging station, and it, in turn, to the mains ...
Using small accumulator:
It could happen, then after prolonged work, the hand will get tired of the weight of the machine. This is especially
true for girls masters. Hand fatigue is caused not only by the weight of the machine, but also by its center of gravity. A
small battery greatly facilitates the device, and most importantly transfers the center of mass from behind the wrist to the
metacarpal bones, which almost completely removes the effect of "pulling" the hand off by the machine. Of course, this
arrangement has a drawback - the operating time from a small battery is several times lower than that of a full-fledged
one. Use what works best for your situation.
Installing the battery 18350: Insert the battery into the car with the negative * contact towards you. Insert the battery
tab with the flat, metal end facing you. Screw on the back cover. All other aspects of working with a small battery are
identical to the standard one.