MSI MS-6191 Micro ATX IR2 Manual Download

Page: 70 / 86

CHAPTER 3

AMI

BIOS USERS GUIDE

3-12

Spread Spectrum

This item allows you to seclect the clock generator Spread Spec-

trum function. the default is Enabled. This item should always be set to
Disabled, if you overclock the processor. If you set to Enabled, it will work
better for EMI test.

Stop Un-used PCI/DIMM Clock

During Enabled, any unpopulated DIMM socket or PCI slot will be

non-operational. During Disabled, all DIMM socket or PCI slot will be
operational. The default setting is Enabled.

USB Function

Set this option to Enabled or Disabled the on-chip USB controller.

The Optional and Fail-Safe default settings are Disabled.

USB KB/Mouse Legacy Support

Set this option to Enabled or Disabled USB Mouse & keyboard.

The Optional and Fail-Safe default settings are Disabled.

Summary of Contents for MS-6191 Micro ATX IR2























































































Search results

Summary of Contents for MS-6191 Micro ATX IR2

Reviews:

Related manuals for MS-6191 Micro ATX IR2

Brands by name

Popular brands

MSI MS-6191 Micro ATX IR2, Manual

Search results

Summary of Contents for MS-6191 Micro ATX IR2

Reviews:

Related manuals for MS-6191 Micro ATX IR2

Brands by name

Popular brands