manualshive.com logo in svg

MSE Kestrel, User Manual, Page: 11 / 31

Share
Download
MSE Kestrel User Manual Download Page 11

 

TECHNICAL DATA 

 

 

 

 

11 

 

2.  TECHNICAL DATA   

 

Manufacturer

  

 

 

 

            

MSE CENTRIFUGES Ltd 

 
Type

 

 

MSB015.CX1.5 (240 V) 

   

 

MSB015.CX1.1 (110 V) 

 
Mains  L1+N+PE          V/Hz  ±10%                              230 V 50/60 Hz 
   

 

110 V 50/60 Hz 

 
 
Maximum power consumption 

 

70 W  

Maximum capacity 

 

90 ml  

Maximum rotational speed 

 

6000 rpm   

Maximum acceleration 

 

3340 x g  

Maximum kinetic energy 

 

Nm  

Timer 

 

1 - 60 min  

   

 

15 second increments  

Interference level  

 

PN-EN-55011 

Noise level 

 

56 dB 

    

 

 

Physical data:  

 
Depth 

 

270 mm  

Width  

 

220 mm  

Height 

 

180 mm  

Weight  

 

5 kg  

   

 

Environmental conditions:

                                          

PN-EN-61010-1 (point 1.4.1.)  

 
Ambiant temperature  

 

+5

°

 to +36

°

 C  

Relative humidity at ambient temperature  

 

<

 80 %  

Installation category  

 

II PN-EN 61010 - 1 

Degree of pollution  

 

2 PN-EN 61010 - 1 

Protection zone  

 

300 mm

 

 

 

2.1  Statement of Conformity 

 

The following machine is in accordance with the regulations of the EU Directive 
98/79/EC and with the harmonized standards PN-EN 61010-1 and PN-EN 61010-2-
020. 

Summary of Contents for Kestrel
































Reviews:

No comments