background image

 

 

Safety Information 

10 

2

 

Safety Information 

2.1

 

Regulatory and Safety Certifications 

The SECTOR S 600 has been tested to comply with applicable regulatory standards; it carries the cSGSus mark and is CE marked. 
Regarding EN 61326-1: 2013 Electrical Equipment for Measurement, Control, and Laboratory Use – EMC Requirements:  

 

The SECTOR S 600 instrument is designed for operation in a controlled electromagnetic environment. Transmitters of RF 
energy such as mobile (cellular) telephones should not be used in close proximity. 

Regarding FCC Rules, Part 15, Subpart B, a Class A digital device: 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC 
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated 
in a commercial environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause interference in which case the user will be required to correct the 
interference at his own expense. 

Regarding Industry Canada Interference-Causing Equipment Standard: 

 

This Class A digital apparatus complies with CAN ICES-001(A). 

 

Cet appareil numérique de la Classe A est conforme à la norme NMB-001(A) du Canada. 

Contact MS

Scientific Support

 with inquiries about the regulatory compliance of MSD instrumentation. 

2.1.1

 

WEEE Compliance 

The MESO SECTOR S 600 was placed on the market after 2005 in compliance with European Union (EU) directive 2012/19/EU, the 
Waste Electrical and Electronic Equipment (WEEE) Directive. 
For all inquiries regarding recycling of shipping materials and instrument disposal, contact MS

Instrument Service

 

 

Summary of Contents for MESO SECTOR S 600



























































Reviews: