MSA UNICORNT PS-203-50 Operating Manual Download Page 15

Power supply unit 

PS-203-50 

 

 

Page 15  

 

        Version 1.0 

 

7

 

DISPOSAL 

New  equipment,  the  parts  of  the  Product  damaged  during  operation,  and  any 

outage  equipment  must not be disposed as  standard household  wastes, since  they  con-
tain the materials suitable for re-use. 

Decommissioned and non-used components of the Product must be delivered to 

a special waste disposal center licensed by local authorities. You can also send an over-
age equipment/unit to the manufacturer for its further disposal. 

Proper disposal of Product components allows avoiding possible negative envi-

ronmental  and  health  impacts,  and  it  also  allows  for  proper  restoration  of  components 
with substantial energy and resources saving.  

During  operation  and  upon  completion  of  its  service  life,  the  equipment  is  not 
hazardous for health and environment

 

 

This unit must be disposed according to the rules applied to electronic devices

 

 

Any  products  marked  with  a  crossed  trash  bin  must  be  disposed  sepa-
rately from standard household wastes

 

Summary of Contents for UNICORNT PS-203-50


















Reviews: