MSA Firehawk Responder Series Maintenance And Repair Manual Download Page 4

FIREHAWK RESPONDER SECOND STAGE REGULATOR

DISASSEMBLY

Removing the Regulator Cover and Spring

1. Remove the regulator cover.

a. Press and hold the

release buttons while
pressing the
regulator housing
retaining latches.

b. Allow the cover to

drop into your palm.

c. Remove the spring

from the regulator
cover.

Note:

Do not stretch the spring.

Removing the Diaphragm

1. Remove the CBRN Shield.

Handle the CBRN shield by the rim only.

a. Lift the CBRN

shield assembly
and spring cap
off of the diaphragm
assembly.

b. Lift the spring cap

off of the CBRN
shield assembly.

4

TAL 016 (L) Rev. 3 - 10096394

Table of Contents

Disassembly

......................................................................4

Regulator Cover and Spring ...........................................4
Diaphragm ......................................................................4
Bypass Assembly ...........................................................5
Bypass Screen................................................................6
Valve Assembly...............................................................6
Regulator Housing Buttons ............................................6
Seal Ring.........................................................................7

Inspection of the Valve Fork for Proper Height

............7

Acceptable Valve Fork Heights ......................................8
Adjusting Valve Fork Height for Proper Performance ....8

Adjustment of Valve Fork if Above the Maximum ..........8
Adjustment of Valve Fork if Below the Minimum ...........8

Reassembly

.......................................................................9

Seal Ring.........................................................................9
Regulator Housing and Buttons .....................................9
Valve Assembly...............................................................9
Bypass Screen..............................................................10
Bypass Assembly .........................................................10
Diaphragm ....................................................................12
Regulator Cover............................................................12

Latches

Spring

Summary of Contents for Firehawk Responder Series














Reviews: