background image

INTRODUCTION

BB - Not for use in entry into atmospheres immediately

dangerous to life or health.

CC - For entry, do not exceed maximum use concentra-

tions established by regulatory standards.

GG - Direct contact with CBRN agents requires proper

handling of the respirator after use. Correct dispos-
al procedures must be followed.

QQ - Use in conjunction with personal protective ensem-

bles that provide appropriate levels of protection
against dermal hazard. Failure to do so may result
in personal injury even when the respirator is fitted
properly, used, and maintained.

UU - The respirator should not be used beyond eight (8)

hours after initial exposure to chemical warfare
agents to avoid the possibility of agent permeation.
If liquid exposure is encountered, the respirator
should not be used for more than two (2) hours.

VV -

PAPRS with TC-23C approvals may NOT be used
for escape from IDLH atmospheres.

S – SPECIAL OR CRITICAL USER’S INSTRUCTIONS

1. During use of the FireHawk M7 Responder PAPR, the

atmosphere must be monitored for the level of conta-
mination and a means of escape must be provided in
the event that the contamination level increases to
immediately dangerous to life and health (IDLH) levels.

2. The C420 PAPR must be properly inspected before

use, properly decontaminated, if necessary, after use,
properly cleaned and maintained after use, and prop-
erly stored between uses.

3. The C420 PAPR contains a battery and may not be

taken into or used in atmospheres containing flamma-
ble or explosive gases, vapors, or dusts when the
concentration of such contaminants is near or above
the lower flammable limit (LFL).

4. Do not use the C420 PAPR for firefighting, in oxygen-

deficient atmospheres, or for protection against air-
borne contaminants from which the canister does not
protect.

5. Firehawk

®

Regulator must always be connected to the

inlet adapter when used as a CBRN APR Respirator or
CBRN PAPR Respirator.

6. The Firehawk Regulator is a non-functional compo-

nent as regulator, but is functional as a plug for the
front port.

DO NOT attach the regulator to supplied air while
using the respirator as a CBRN APR or CBRN PAPR.
Failure to follow this warning can result in serious per-
sonal injury or death.

This respirator is approved for APR OR PAPR only
configurations and is not intended to be combined
with other apparatus. Failure to follow this warning
can result in serious personal injury or death.

7. The FireHawk M7 Heads-Up-Display (HUD) compo-

nents are non-functional component while attached to
the FireHawk M7 Responder APR when used as a
CBRN APR or CBRN PAPR.

8. The FireHawk M7 HUD is an optional component for

FireHawk M7 Responder APR or PAPR. The HUD can
be removed or attached prior to use.

9. The mouth-bit can be inserted or removed from the

nosecup prior to use. Please read the “Preparing the
Respirator for Use” section for proper procedure.

Follow instruction in the “Preparing the Respirator for
Use” section of the FireHawk M7 Responder APR user
instructions before inserting or removing the mouth-
bit in the nosecup. Failure to follow this warning can
result in serious personal injury or death.

The nosecup must always be installed when using the
FireHawk M7 Responder APR or PAPR. Failure to fol-
low this warning can result in serious personal injury
or death.

When using filters in an application that produces
sparks, ensure that they are protected by a shield.
Contact with sparks can damage filters and reduce
protection.

3

TAL 804 (L) Rev. 0 - 10086003

Summary of Contents for FireHawk M7 Responder PAPR

























Reviews: