background image

REMOVING THE APPARATUS

3.  Loosen the screws to open battery door.
4.  Insert two AAA batteries according to the battery ori-

entation noted inside the compartment.

5.  Close the battery door and tighten the screws.
6.  Slide shroud over transmitter and fasten strap(s).

Use only Duracell MN1500 or Energizer E91 AA alka-
line batteries in the RECEIVER. Use of other batteries,
or a combination of batteries from different manufac-
turers, will affect performance of unit and will void the
Intrinsic Safety approval. Failure to follow this warning
can result in serious personal injury or death.

Note: 

For older versions of the Nightfighter RECEIVER

containing AAA Alkaline batteries, use only Duracell
MN2400, Energizer E92, or Eveready A92. Use of other
batteries, or a combination of batteries from different
manufacturers, will affect performance of unit and will
void the Intrinsic Safety approval.

1.  Loosen the screws to open the battery door in the

receiver.

2.  Insert two AA batteries according to the battery orien-

tation noted inside the receiver compartment.

3.  Inspect the battery cover gasket is free of debris and

not damaged or missing.

4. Close the battery door and tighten the screws.

Battery Disposal/Recycling

Dispose of or recycle batteries in accordance with all
applicable federal, state, and local regulations.

Do not dispose of the battery in fire. It may explode.
Failure to follow this warning can result in serious per-
sonal injury or death.

16

TAL 601 (L) Rev. 5 - 10041214

WARNING

WARNING

Summary of Contents for BlackHawk MMR





























Reviews: