MSA Abrasi-Blast Series Instructions Manual Download Page 16

Page: 16 / 24

TAL 201 (L) Rev. 1 - 818366

Facepiece Assemblies

Carton of 12

No. of Lenses

One Cartridge

Part No.

Description of Lens

In Each Cartridge

Part No.

Application

473798

.09 thick untempered

473795

Medium abrasive blasting

473800

.09 thick tempered

473796

Same as above with added protection against breakage
due to rough handling

473802

.12 thick untempered

473797

Heavy abrasive blasting

two layers laminated

481742

.12 thick untempered

481714

Heavy abrasive blasting

two layers laminated

Demand (Single Valve)

SIZE

RUBBER

SMALL MEDIUM

LARGE

PART

Model

Hycar Silicone

NUMBER 7-434-2 7-434-1

7-434-3

473314

•

473312

•

473316

•

PROTECTIVE LENS CARTRIDGES

Demand (Dual Valve)

SIZE

RUBBER

SMALL MEDIUM

LARGE

PART

Model

Hycar Silicone

NUMBER 7-410-2 7-410-1

7-410-3

472668

•

472666

•

472670

•

Pressure Demand

SIZE

RUBBER

SMALL MEDIUM

LARGE

PART

Model

Hycar Silicone

NUMBER 7-780-2 7-780-1

7-780-3

485772

•

485768

•

485776

•

818366_a.qxd 1/24/02 3:18 PM Page 16

Summary of Contents for Abrasi-Blast Series

























Search results

Summary of Contents for Abrasi-Blast Series

Reviews:

Brands by name

Popular brands

MSA Abrasi-Blast Series, Instructions Manual

Search results

Summary of Contents for Abrasi-Blast Series

Reviews:

Brands by name

Popular brands