background image

Abrasi-Blast

TM

Respirator

instructions

The warranties made by MSA with respect to the product are voided if the product
is not installed, used, and serviced in accordance with the instructions in this
manual. Please protect yourself and your employees by following the instructions.
Please read and observe the WARNINGS and CAUTIONS inside. We encourage
our customers to write or call for a demonstration of this equipment prior to use
or for any additional information relative to use or repairs. Call 1-800-MSA-2222
during regular working hours.

This manual must be read carefully by all persons who have or will have the
responsibility for using or servicing the product. Like any complex piece of
equipment, the Abrasi-Blast Respirator from MSA will perform as designed only
if it is used and serviced according to the instructions. Otherwise, it could fail
to perform as designed, and persons who rely on this respirator could sustain
serious personal injury or death.

TAL 201 (L) Rev. 1

© MSA 2002

Prnt. Spec. 10000005389 (A) Mat. 818366

Doc. 818366

818366_a.qxd  1/24/02  3:18 PM  Page 1

Summary of Contents for Abrasi-Blast Series

























Reviews: