background image

 

ii

Studiobot XL Quick Start Guide

QSG Product Code: MRMC-2139-01

Product Covered: MRMC-2011-01

© 2021 Mark Roberts Motion Control Ltd. All rights reserved. 

No part of this publication may be reproduced, transmitted, or translated 
by any means — graphical, electronic, or mechanical — including 
photocopying, recording, taping, or storage in an information retrieval 
system, without the express written permission of Mark Roberts Motion 
Control. 

Although every care has been taken to ensure that the information in this 
document is accurate and up to date, Mark Roberts Motion Control 
continuously strives to improve their products and may make changes to 
the hardware, firmware, and software described in this document. Mark 
Roberts Motion Control therefore cannot be held responsible for any 
error or omission in this document. 

All product names mentioned herein are the trademarks or registered 
trademarks of their respective owners. 

Contact information

Mark Roberts Motion Control Ltd.

  

Unit 3, South East Studios 
Blindley Heath 
Surrey  
RH7 6JP 
United Kingdom 

Telephone: 

+44 (0) 1342 838000 

E-mail:

[email protected] (sales and general enquiries)  
[email protected] (customer support) 

Web:

www.mrmoco.com  
www.mrmocorentals.com 

Summary of Contents for MRMC-2011-01













































Reviews: