MR VACUTAP VR Installation And Commissioning Instructions Download Page 219 | Manualshive

Page: 219 / 268

background image

11 Commissioning transformer at installation site

Maschinenfabrik Reinhausen GmbH 2015

219

4349315/00 EN

VACUTAP® VR®

Checking pressure monitoring device

ü

Check that the pressure monitoring device is operating properly before
putting the transformer into operation:

1.

Ground the transformer on the high-voltage and low-voltage sides. En-
sure that the working ground connection on the transformer is not re-
moved during testing.

2.

Ensure that transformer remains de-energized during testing.

3.

Deactivate the automatic fire extinguishing device.

4.

Remove the cover cap.

5.

Activate the sensor on the snap-action switch.

ð

Sensor is in the OFF position.

6.

Leave the transformer's danger zone.

7.

Ensure that the transformer's circuit breaker cannot be closed.

ð

Passive protection test

8.

Activate the sensor on the snap-action switch.

ð

Sensor is in the OPERATION position

9.

Leave the transformer's danger zone.

10. Close the transformer's circuit breaker with isolating switches open and

the transformer grounded on all sides.

11. Activate the sensor on the snap-action switch.

ð

Sensor is in the OFF position.

12. Ensure that the transformer's circuit breaker is open.

ð

Active protection test.

13. Activate the sensor on the snap-action switch to reset the pressure

monitoring device.

ð

Sensor is in the OPERATION position

14. Secure the cover cap.

Filling the oil compartment of the on-load tap-changer with
oil

WARNING

Danger of death or severe injury!

Danger of death or severe injury from explosive gases under the on-load
tap-changer head cover, in the pipework system, in the oil conservator or at
the dehydrating breather opening!
► Ensure that there are no naked flames, hot surfaces or sparks (for ex-

ample caused by static charging) in the immediate surroundings and
that none occur.

11.3

11.4

«
...
217
218
219
220
221
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Related manuals for VACUTAP VR

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Dairyland Pages: 21

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

COOPER POWER SERIES

Brand: Eaton Pages: 8

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brand: laerdal Pages: 32

Brand: laerdal Pages: 32

Brand: laerdal Pages: 8

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Sagola Pages: 62

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands