MR VACUTAP VR-Ex Installation And Commissioning Instructions Download Page 41

Page: 41 / 256

5 Mounting

Maschinenfabrik Reinhausen GmbH 2020

7545652/00 EN

VACUTAP

VR-Ex

2. Fit stud bolts on mounting flange.

Figure 16: Tracing template, stud bolts

5.3 Installing the on-load tap-changer in the transformer

(standard version)

5.3.1 Fastening on-load tap-changer to transformer cover

5.3.1.1 Fastening oil compartment to transformer cover – standard on-load

tap-changer head version

You can lower the oil compartment of on-load tap-changers with U

362 kV through the opening in the mounting flange without separating the
top part of the on-load tap-changer head from the bottom part.

CAUTION!

An unstably positioned oil compartment may tip over, re-

sulting in injuries or property damage. Place the oil compartment on a
level surface and secure it against tipping.

2. Remove red-colored packaging material and transport material from the

oil compartment.

Summary of Contents for VACUTAP VR-Ex

































































































































































































































































Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands

MR VACUTAP VR-Ex, Installation And Commissioning Instructions

Search results

Summary of Contents for VACUTAP VR-Ex

Reviews:

Related manuals for VACUTAP VR-Ex

Brands by name

Popular brands