mr. steam iSteam 3 Control, Installation, Operation & Maintenance Manual

Page: 5 / 16

4
INSTALLER INFORMATION
®
3a
3b
4a
4a
5b
5a
Locating the Control
Determine the desired installation location of the control. The iSteam
®
3
controls are designed to be installed inside or outside the steam room
as a matter of personal preference. If the control is installed inside
the steam room:
U œV>ÌiÊÌ iÊVœ˜ÌÀœÊ{‡xÊviiÌÊ>LœÛiÊÌ iÊyœœÀʘi>ÀÊÌ iÊL>Ì iÀÊÃi>̈˜}Ê>Ài>°
U / iÊVœ˜ÌÀœÊvi>ÌÕÀiÃÊ>˜Êˆ˜Ìi}À>ÊÌi“«iÀ>ÌÕÀiÊÃi˜ÃœÀ°ÊœV>ÌiÊÌ iÊVœ˜ÌÀœÊˆ˜Ê>
location representative of the desired steam bathing temperatures. Do not
locate the control above or near the steam head or direct steam emissions.
U œV>ÌiÊÌ iÊVœ˜ÌÀœÊœ˜Ê>ÊÛiÀ̈V>ÊÜ>°
U / iÊVœ˜ÌÀœÊV>LiʈÃÊÎäÊviḭʘÃÕÀiÊÌ >ÌÊÌ iÊVœ˜ÌÀœÊ>˜`ÊÃÌi>“Ê}i˜iÀ>̜ÀÊ>Ài
located accordingly.
IMPORTANT NOTES:
U vÊÀiµÕˆÀi`]ÊVœ˜Ì>VÌÊÀ-Ìi>“Ê̜ʫÕÀV >ÃiÊ>˜Êœ«Ìˆœ˜>ÊÈä½Êˆ-Ìi>“Î
control cable part number 104117-60.
U vÊÌ iÊVœ˜ÌÀœÊˆÃʈ˜ÃÌ>i`ʜÕÌÈ`iÊÌ iÊÃÌi>“ÊÀœœ“Ê>Ê,i“œÌiÊ/i“«iÀ>ÌÕÀi
Probe Part Number MSTS must be installed inside the steam room.
Refer to the MSTS installation manual before installing the control.
U ˜ÃÕÀiÊÀ-Ìi>“ÊÃÌi>“Ê}i˜iÀ>̜ÀʈÃʈ-Ìi>“ 3 compatible and has
a serial number 1174000 or higher.
Installation with Optional Rough-In Box
A rough-in box is supplied with iSteam3 for new construction. The rough
-in box will allow precise location of the iSteam3 control and provide a
secure and easily identifiable place for the cable while the steam room is
being constructed.
STEP 1
Take the rough-in box out of the package. Remove the two
screws (1a ) and place them in the top and bottom wings of the rough-in
box (1b).
STEP 2
Select a KNOCK-OUT (2a) to route the control cable into the box.
STEP 3
Line up the two TABS (3a) on the right side of the box against a
stud. These TABS help locate the box to sit PROUD of the stud (3b).
STEP 4 SCREW (4a) the two supplied screws into the stud.
STEP 5
Route the CONTROL CABLE (5a) through the back of the rough-in
box and clip it under one of the TABS (5b) that previously held the screws.
The two ends of the control cable are the same.
IMPORTANT NOTE: The control cable should be run in a dedicated 1”
conduit to facilitate installation and service.
1a
1b
1b
2a