background image

Installation instructions and Owner’s Manual

1

ENERCO GROUP, INC., 4560 W. 160

TH

 ST., CLEVELAND, OHIO 44135 · 216-916-3000

WARNING:

  If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- An LP cylinder not connected for use shall not be stored in the vincinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Shut off gas supply

• Do not try to light any appliance

• Do not touch an electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING

:  This is an unvented gas-fired heater.  It uses air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and Ventila-
tion section on page 3 of this manual.

WARNING

: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage.  Refer to this manual for correct installation and operational procedures.  For assistance or additional
information consult a qualified installer, service agency, or gas supplier.

70586   04/06

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY:

 Read and follow all instructions. Place

instructions in a safe place for future reference. Do not allow anyone who has not read

these instructions to assemble, light, adjust or operate the heater.

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

MR. HEATER

MODEL

MHVFB10LP

UNVENTED LP-GAS FIRED
BUDDY WALL-MOUNT HEATER

Summary of Contents for Blue Flame MHVFB10LP

















Reviews: