manualshive.com logo in svg

MQ Power DCA300SSC WHISPERWATT SERIES, Operation And Parts Manual, Page: 24 / 92

Share
Download
MQ Power DCA300SSC WHISPERWATT SERIES Operation And Parts Manual Download Page 24

PAGE 24 — DCA300SSC GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (06/25/09) 

OUTPUT TERMINAL PANEL FAMILIARIZATION

Connecting Loads

Loads can be connected to the generator by the 

Output 

Terminal Lugs

 or the convenience receptacles (Figure 10). 

Make sure to read the operation manual before attempting 
to connect a load to the generator.

To protect the output terminals from overload, a 3-pole, 
800A 

main

 circuit breaker is provided. Make sure to switch 

ALL

 circuit breakers to the 

OFF

 position prior to starting 

the engine.

Connecting Loads

Figure 10. 

Over Current Relay

An 

over current relay

 (Figure 11) is connected to the main 

circuit breaker. In the event of an overload, both the circuit 
breaker and the over current relay may trip. If the circuit 
breaker can not be reset, the 

reset button

 on the over 

current relay must be pressed. The over current relay is 
located in the control box.

Over Current Relay

Figure 11. 

Summary of Contents for DCA300SSC WHISPERWATT SERIES





























































































Reviews:

No comments