MPS MP1591 Manual Download Page 10

MP1591 – 2A, 32V, 330KHz STEP-DOWN CONVERTER 

 

MP1591 Rev. 2.3 

www.MonolithicPower.com 

10

 

9/21/2007 

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 

 

© 2007 MPS. All Rights Reserved. 

PACKAGE INFORMATION 

SOIC8 

0.016(0.41)
0.050(1.27)

0

o

-8

o

DETAIL "A"

0.010(0.25)
0.020(0.50)

x 45

o

SEE DETAIL "A"

0.0075(0.19)
0.0098(0.25)

0.150(3.80)
0.157(4.00)

PIN 1 ID

0.050(1.27)
BSC

0.013(0.33)
0.020(0.51)

SEATING PLANE

0.004(0.10)
0.010(0.25)

0.189(4.80)
0.197(5.00)

0.053(1.35)
0.069(1.75)

TOP VIEW

FRONT VIEW

0.228(5.80)
0.244(6.20)

SIDE VIEW

1

4

8

5

RECOMMENDED LAND PATTERN

0.213(5.40)

0.063(1.60)

0.050(1.27)

0.024(0.61)

NOTE:

  1) CONTROL DIMENSION IS IN INCHES.  DIMENSION IN
      BRACKET IS IN MILLIMETERS.
  2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH,
      PROTRUSIONS OR GATE BURRS.
  3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH
      OR PROTRUSIONS.
  4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING)
      SHALL BE 0.004" INCHES MAX.
  5) DRAWING CONFORMS TO JEDEC MS-012, VARIATION AA.
  6) DRAWING IS NOT TO SCALE.

0.010(0.25) BSC

GAUGE PLANE

Summary of Contents for MP1591












Reviews: