AC operation
1. Insert the DC power jack of the AC/DC adaptor to the DC input socket located at the back of the unit.
2. Plug the AC/DC Adaptor to the AC mains outlet.
3.
Press the
STANDBY/ON
button on the front panel to turn the radio on.
DC (battery) operation
In DC operation, the
STANDBY/ON
button will work as a
POWER ON/OFF
button. The display will be totally off when
the radio is powered off. The display backlight will be dimmed after radio power on, and it will be turned on to full
brightness for 5 seconds on every key press.
1. Ensure the AC/DC adaptor is disconnected from the radio and AC mains.
2.
Installed the batteries (4X1.5V UM3/AA battery) into the battery compartment.
3.
Press the
STANDBY/ON
button on the front panel to toggle the radio between on and off.
Note:
To obtain the best performance in DC operation, the use of alkaline batteries is highly recommended.
Clock setting
The clock will only set and be updated if you can receive DAB signals in your location. In order for the clock to
synchronise to the current local time you must leave it one DAB station for a short period. Manual clock setting is not
required.
LISTENING TO YOUR RADIO
Hints for better reception
This radio is fitted with a single DAB/FM telescopic antenna, to obtain the best performance, you should fully extend
the antenna and adjust its position as well as the direction until you find the best reception. For ideal DAB reception,
always maintain the antenna in an upright vertical position is highly recommended.
DAB mode
If the radio is powered up and switched on for the first time, it will automatically enter into the DAB mode and perform
auto scan function. During the scan the display will show “Scanning …” together with a slide bar that indicates the
progress of the scan and the amount of stations that have been found so far. (F. 1) (F. 2)
Once the scan has finished, the radio will select the first alphanumerically found station. You can now press the
▲
or
▼
button to explore the found stations and then press the
SELECT
button to select your station.
SWITCHING YOUR RADIO ON FOR THE FIRST TIME
When the radio is connected to the AC power (via the AC/DC adaptor) for the first time, it will be in standby mode.
The display backlight will be on for a few seconds, the display will first show the greetings and finally the clock. Press
the
STANDBY/ON
button once to turn the radio on, it will then automatically enter into the DAB mode and perform
auto scan function.
UK-3
UK-2
Simple DAB/FM Digital Radio
INSTRUCTION MANUAL
FEATURES
AND
CONTROLS
11. ANTENNA
12. VOLUME CONTROL
13. HEADPHONE JACK
14. DC INPUT SOCKET
15. BATTERY DOOR
1. SPEAKER
2. INFO BUTTON
3. MENU BUTTON
4. SELECT BUTTON
5.
BUTTON
▼
6. DAB/FM BUTTON
7. LCD DISPLAY
8. PRESET BUTTON
9. STANDBY/ON BUTTON
10.
BUTTON
▲
14
15
11
12
13
1
2 3
4
5
6
7
8
9
10
UK-1
To achieve the utmost in enjoyment and performance, and in order to become familiar with its features, please read this manual carefully
before attempting to operate the unit.
Important Notes
This safety and operating instruction should be retained for future reference.
The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on
apparatus. Avoid installing the unit in locations described below:
* - Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters,
on top of other stereo equipment that radiate too much heat.
* - Places blocking ventilation or dusty places.
* - Places subject to constant vibration, humid or moist places.
No naked flame sources such as lighted candles should be placed on the unit.
Attention should be drawn to the environmental aspects of battery disposal.
Make sure not to obstruct the ventilation openings, a minimum of 10cm should be kept around the apparatus for ventilation.
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains,
etc.Use apparatus in moderate climates only.
Operate tuning controls and switches as instructed in the manual.
The normal function of the product may be disturbed by Strong Electro Magnetic Interference. If so, simply reset the product to
resume normal operation by following the instruction manual. In case the function could not resume, please use the product in
other location.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside, refer all servicing
to qualified service personnel.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK), NO USER SERVICEABLE
PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE
Conductor dangerous voltage, that may be of sufficient magnitude to constitute a risk of electric shock to persons is
present within this product's enclosure.
ATTENTION
The owner's manual contains important operating and maintenance instructions, for your safety, it is necessary to refer
to the manual.
WARNING :TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING
.
Note:
This unit will become warm when used for a long period of time. This is normal and does not indicate a problem with the
unit.This unit includes micro-processors which may malfunction as a result of external electrical interference/ noise or electrostatic
discharge. If the unit is not working properly, disconnect the power source and then reconnect it.
The AC/DC adaptor is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use.
To be completely disconnected the apparatus from supply mains, the AC/DC adaptor of the apparatus shall be disconnected from the
mains socket outlet completely.
DAB120
