manualshive.com logo in svg

MPE CHAIN-VEY, Installation & Operation Manual

Share
Download
MPE CHAIN-VEY Installation & Operation Manual Download Page 17

                                                               

 

 

16 

4. Flow Control 

 

When there is a bulk source or direct head-load of product feeding the Chain-Vey conveyor, the 
inlet flow control baffle is very important.  The flow control baffle utilizes two plates on a pivot 
which increase or decrease the opening of the inlet.  Two hand knobs are used to adjust and also 
lock the plates' position once the desired feed rate is attained.  If desired, a tamper-resistant, tooled 
adjustment is an available alternative to the hand knobs. 
 

  

 

 

Note: 

To prevent product shear and reduce excessive pull on the chain, the inlet and baffle must be 
installed in accordance with the conveying direction as shown above. 
 

 

 

Low Fill 

(< 50%) 

 

 

Standard Fill 
(70% - 80%) 

 

 

Maximum Fill 

(90%)

 

To achieve desired fill level, adjust the baffles of the inlet flow control, and make adjustments to 
the conveyor speed and feed rate. 

 
 

Summary of Contents for CHAIN-VEY



























Reviews:

No comments

Brands by name

Popular brands

Load more brands