manualshive.com logo in svg

Moxa Technologies ioPAC 8500 series, Hardware User Manual

Share
Download
Moxa Technologies ioPAC 8500 series Hardware User Manual Download Page 15

ioPAC 8500 Hardware 

Installation 

 

2-5 

 

ATTENTION 

This product is intended to be supplied by a Listed Power Unit with output marked “LPS” and rated for 9-48 VDC 
(minimum requirements). For railway rolling stock applications, these devices must be supplied by a galvanic 
isolated power supply with design based on the EN 50155 standard. 

 

Installing a microSD Card 

The ioPAC is equipped with one slot for a microSD card. The card reader slot is located inside the ioPAC device, 
so you will need to unscrew and remove the card cover to install your microSD card. When inserting a microSD 
card, remember to keep the front edge of the card facing down. 

Follow these steps to remove or install a microSD card: 

1.

 

Remove the screw holding the card cover in place. 

 

2.

 

(a) Insert the microSD card into the microSD card slot, or 
(b) Remove the microSD card from the microSD card slot. 

 

3.

 

Fasten back the screw holding the card cover in place. 

 
 
 
 
 

Summary of Contents for ioPAC 8500 series



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands