– 4 –
– 5 –
– 6 –
www.moxa.com/support
The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)
Europe: +49-89-3 70 03 99-0
Asia-Pacific: +886-2-8919-1230
China: +86-21-5258-9955 (toll-free: 800-820-5036)
2011 Moxa Inc. All rights reserved.
4.
If you see a warning that the software has not passed Windows
Logo testing, select
Continue Anyway
.
5.
After the driver software has been installed, the installation
wizard will guide you through the port installation, starting
with port 0. Be sure to install the software from the
\
CP-114UL\Software\Windows 2K
folder on the CD.
6.
To verify successful installation, use
Windows
Device
Manager
and check under
Multi-port serial adapters and
Ports (COM & LPT)
for any special marks, such as a question
mark or exclamation point.
Linux (32-bit/64-bit)
Ensure that you are logged into the machine with superuser (root)
privileges. Insert the Moxa driver CD-ROM into the CD-ROM drive.
If necessary, use the
mkdir
command to create a mount point for
the CD-ROM. The following command creates a mount point in the
directory /cdrom; you can mount the CD-ROM at any location in
the machine’s local file system.
mkdir /cdrom
The commands in the steps below assume the CD-ROM is mounted
at /cdrom. If you mount the CD-ROM at a different location, use
that location when issuing commands.
Mount the CD-ROM drive by entering the following command:
# mount -t iso9660 -o ro /dev/cdrom /cdrom
1.
Execute the following commands from the Linux prompt:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver directory>/mxser.tgz .
#tar xvfz mxser.tgz
#cd mxser
#make clean; make install
#cd /moxa/mxser/driver
#./msmknod
#modprobe mxser
2.
Use the Moxa diagnostic utility to verify the driver status:
#cd /moxa/mxser/utility/diag
#./msdiag
3.
Use the Moxa terminal utility to test the TTY ports:
#cd /moxa/mxser/utility/term
#./msterm #./msterm
Pin Assignments and Cable Wiring
The CP-112UL series has a female DB25 connector on the board.
Cables with different connectors are available to help you connect
your device to the board.
Male DB9 (CBL-M25M9x2-50)
Pin RS-232 RS-422 RS-485
4-wire
RS-485
2-wire
1
DCD
TxD-(A) TxD-(A) –
2
RxD
TxD+(B) TxD+(B) –
3
TxD
RxD+(B) RxD+(B) Data+(B)
4
DTR
RxD-(A) RxD-(A) Data-(A)
5
GND
GND
GND
GND
6
DSR
–
–
–
7
RTS
–
–
–
8
CTS
–
–
–
The CP-114UL series has a female DB44 connector on the board.
Cables with different connectors are available to help you connect
your device to the board.
Male DB9 (CBL-M44M9x4-50)
Pin RS-232 RS-422 RS-485
4-wire
RS-485
2-wire
1
DCD
TxD-(A) TxD-(A) –
2
RxD
TxD+(B) TxD+(B) –
3
TxD
RxD+(B) RxD+(B) Data+(B)
4
DTR
RxD-(A) RxD-(A) Data-(A)
5
GND
GND
GND
GND
6
DSR
–
–
–
7
RTS
–
–
–
8
CTS
–
–
–
Male DB25 (CBL-M44M25x4-50)
Pin RS-232 RS-422 RS-485
4-wire
RS-485
2-wire
2
TxD
RxD+(B) RxD+(B) Data+(B)
3
RxD
TxD+(B) TxD+(B) –
4
RTS
–
–
–
5
CTS
–
–
–
6
DSR
–
–
–
7
GND
GND
GND
GND
8
DCD
TxD-(A) TxD-(A) –
20 DTR
RxD-(A) RxD-(A) Data-(A)
