background image

 

 

 

 

type, sont strictement interdits pour une utilisation avec cet appareil. 
 

Caution: 

i.) the device for operation in the band 5150

–5250 MHz is only for indoor use to reduce the potential for 

harmful interference to co-channel mobile satellite systems; 

Mise en garde: 

i.)  le  dispositif  destiné  à  fonctionner  dans  la  bande  5150

–5250  MHz  est  destiné  uniquement  à  une 

utilisation  en  intérieur  afin  de  réduire  le  risque  de  brouillage  préjudiciable  causé  par  les  systèmes 
mobiles à satellites dans le même canal; 
 

Caution: 

i.) the device for operation in the band 

5250

–5350

 MHz is "for indoor use only".

 

Mise en garde: 

i.)  le  dispositif  destiné  à  fonctionner  dans  la  bande  5250

–5350  MHz  est  "pour  usage  intérieur 

uniquement". 
The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in 
the above sections, namely that:   
 
i. the device for operation in the band 5150

–5250 MHz is only for indoor use to reduce the potential for 

harmful interference to co-channel mobile satellite systems; 
 
ii. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 
5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;   
 
iii. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 
5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and   
 
iv.  where  applicable,  antenna  type(s),  antenna  models(s),  and  worst-case  tilt  angle(s)  necessary  to 
remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly 
indicated 
 

 

Summary of Contents for AWK-3252A Series


















Reviews: