manualshive.com logo in svg

Movea MotionController, User Manual

Share
Download
Movea MotionController User Manual Download Page 15

 

 

 

 

 

 

15 

IX.

 

CLEANING 

1.

 

CLEANING THE MOTIONCONTROLLER™ 

The MOTIONCONTROLLER™ is made of ABS plastic. Frequent disinfection or cleaning is not needed 
because it’s not in contact with the patient. 

Disconnect the MOTIONCONTROLLER™ before cleaning. Use a soft and dry napkin. 

2.

 

CLEANING THE MOTIONPOD™ 

MOTIONPOD™ and the mechanical interface are made of natural polycarbonate (for the transparent 
cover)  and  of    “Glass  polycarbonate  “”  (the  Black  bottom  cover,  and  mechanical  interface).  The 
button on MOTIONPOD™ is in NBR. For cleaning or disinfection, use products listed below or other 
products  compatible  with  these  materials.  Cleaning  products  must  be  compatible  with 
Polycarbonate. Do not immerse the MOTIONPOD™ in these products. Use a wet paper. 

Example of well adapted cleaning products: HEXANIOS G+R from Anios laboratories 

 (

http://www.anios.com

) 

 

Wet cleaning napkins

 

 

Liquid container

 

 

FIGURE 6 :  WELL ADAPTED DISINFECTION PRODUCTS HEXANIOS G+R 

Summary of Contents for MotionController





















Reviews:

No comments

Brands by name

Popular brands

Load more brands