background image

Report All Incidents

If  your  Movcam  wireless  lens  control  system  performs  in  a 

way that you do not intend or in a way that it is not supposed 

to, contact Movcam Customer Center.

Phone:+86 755 83114888

Fax:+86 755 83115333

Email:[email protected]

Website:http://www.movcam.com

User Guide

Wireless

LensControlSystem

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.  

-- Increase the separation between the equipment and receiver.   

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the 

user's authority to operate the equipment.

Summary of Contents for SCU-1


















Reviews: