Mountup MU0024 Instruction Manual Download Page 2

01

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of 

this product, please contact us.

Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or 

serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed 

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or 

inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. 

ADULT SUPERVISION IS REQUIRED.

NOTE:

 Not all hardware included will be used.

WARNING!

PACKAGE CONTENTS

DO NOT EXCEED WEIGHT CAPACITY.

C (x1)

Clamp Base Support 

D (x1)

Clamp

K (x1)

Wingnut

M (x1)

4mm Allen Key

N (x1)

6mm Allen Key

I(x2)

Security Screw

J(x5)

Bolts

B (x2)

VESA Plate

L (x4 )

Pad

A (x1)

Monitor Stand

E (x1)

Base Support Cover

G (x1)

Base Support

F (x1)

Long Screw

H (x1)

Support Plate

M-E (x8)

D6 Washer

M-C (x8)

M6x12

M-F (x8)

M-B (x8)

M4x16

M-D (x8)

M6x16

M-A (x8)

M4x12

(17.6lbs)x2

(8kg)x2

Summary of Contents for MU0024













Reviews: