Mountfield Extended Oval Assembly And Operation Manual Download Page 10

 

b)

 

through  its  spherical ends – lift the spherical sections  up to their upper position (either at one or both ends of the 
roofing) and secure them by means of the pair of straps provided (see Figs. G and H in Part 10 – 
Illustrated Supplement). 

If the roofed space is occupied, let, at least, either door open to provide for the required air exchange. 
After leaving the roofed space, shut the door by means of zip fasteners, or lower the arches of spherical 
sections down to their low position and secure them against wind by anchors.  
If required, the roofing system can be detached from its anchoring elements and moved away on its 
travelling wheels. 
Before leaving the roofing make always sure that it is properly closed and anchored in the ground. 
 

7.

 

 Safety rules

 

 

 

 

Use the roofing only for the purpose, which it is intended for, i.e. to roof a pool, an outdoor sitting 
area, a car, etc.  

 

This roofing does not constitute any safety system preventing any persons or animals from accessing the 
pool area. Both the roofing manufacturer and seller shall not be responsible for any personal injury or 
damage to property if this warning has not been taken into account.  

 

The assembled roofing must be firmly anchored in the ground by means of the anchors provided 
(see Chapter 5 hereof).  

 

At the time of bathing in the roofed pool the roofing door should be left open, otherwise the 
temperature in the roofed space could increase to a relatively high level, which could cause health 
problems to certain persons staying in the roofed area.  

 

After opening/closing the door and/or end sections the operator shall secure the door and/or the 
lifted/closed door and arches in the open or closed position, as appropriate.  

 

It is strictly forbidden to use any source of open flame in the roofed area because the risk of fire.   

 

If the roofing is used for protecting a car from weather effects, the car engine must not be started 
under the closed roofing. Before starting the engine lift up and secure the supporting arches on the 
side of car exhaust.  

 

In windy weather it is essential to keep the roofing in its closed and secured condition.  

 

It is extremely hazardous to leave the roofing open at its one side, when air has no way out and can 
destroy the roofing, with the resulting risk of damage to property or personal injury.  

 

It is forbidden to open the roofing in strong winds. It could be very hazardous.   

 

Do not load the parts of the roofing structure excessively. Do not suspend any items on the structure. 
The roofing structure is not designed to stand any movement of persons on it, climbing, etc., and 
could collapse.  

 

 

8.

 

Maintenance

 

 

Covering materials should be kept clean. Lukewarm water and mild detergent should be used for the 
purpose.  Do not use any cleaning agents containing/releasing chlorine. 
It is recommended to lubricate the rotational parts (joints, wheel pins, etc.) with silicone lubricant both 
before the start and after the end of the season.  
If the roofing is left outdoor in winter, snow, if any, should be regularly removed from the roofing to protect 
its structure from overloading.  
Do not handle the roofing elements in winter, as its plastic materials get brittle and become more liable to 
damage at low temperatures.   
If it is intended to store the roofing for the winter period, it should be carefully disassembled and stored in 
a dry cold place to protect it from damage.  

 

The manufacturer shall not be responsible for any possible damage caused by any non-observance of the 
instructions contained herein.  

 

 
 

OVAL 

10/17

 

Summary of Contents for Extended Oval


















Reviews: