Slide the UNLOCK switch on the bottom of Camera and use the knob to pull the
slide-out Battery Tray. Install or eight(8) AA size alkaline or lithium batteries
with polarities as indicated in the Battery Tray. Re-install the Battery Tray.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as shown.
Turn Camera on by sliding ON/OFF/IR TEST switch
to the ON position.
Press the MODE button one time to get to the
Camera Setup Menu. Set Time and Date by pressing
ENTER, using UP/DOWN to adjust selected field,
LEFT/RIGHT to move to the next field and ENTER
when done.
Press MODE button until MENU SELECTION
screen is displayed. Use the UP/DOWN buttons
until the MAIN SCREEN option is highlighted
yellow. Press ENTER.
Your Camera will now automatically take pictures
whenever an animal is detected in range -based on
the default settings below.
Eyelet
Mounting
Strap
M-880 GameSpy Digital Camera
PlotStalker Software
Page 3
Page 14
PLOTSTALKER ACTIVITY SEARCH
B
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .mlt photo file, stops
on a photo when changes are found in your identified region, and then highlights
the changes in blue. You can click anywhere in the video viewing area to remove
the blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
1
2
3
Click on the Set Motion Search Area Button.
Use the mouse to select and drag the red outline around the area you want to
search for movement. This allows you to focus on a very precise area if
required.
Click OK button on the Settings Popup window to confirm your settings and
exit the menu.
Set to High, Medium or Low - This sets the level of pixel change the program
will detect. Note; a pixel change will occur with a color, intensity, lighting or
movement so this setting is critical to obtain the desired results.
1
SENSITIVITY
Click on Default button to return to the default values for Search Area and
Sensitivity settings.
GPS Latitude - 000.000000 N
GPS Longitude - 000.000000 W
1
DEFAULT SETTINGS
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
Capture Mode
TRAIL CAM (Still)
Photo Quality
2.0 MP
Photo Delay after each photo is taken
5 SEC
Motion Freeze
ON
Multi Shot Count
OFF
Video Resolution
VGA
Video Length
5 SEC
Video Audio
ON
Camera Name
MOULTRIECAM
Temperature
FAHRENHEIT
Info Strip printed on photos
ON
Plot Frequency
15 SECONDS
Plot Duration
3 HOUR
GPS Longitude & Latitude:
NO
NO
000.000000 N / 000.000000 W
Delete All?
Default Setting
Security Code
00000
QUICK START INSTRUCTIONS
II
DEFAULT SETTINGS
III
Slide the UNLOCK switch on the bottom of Camera and use the knob to pull the slide-out
Battery Tray. Install eight (8) AA size alkaline or lithium batteries with polarities as
indicated in the Battery Tray. Re-install the Battery Tray and insert your SD card.
We recommend that you format the SD card inside the camera before taking pictures.
Thread the provided Mounting Strap through the Eyelets on the back of the camera and
secure to a tree or pole approximately 36” from the ground as shown.
NOTE: Camera must
be attached to a stable object for motion detection to function properly.
Turn camera on by sliding ON/OFF/AIM switch to the ON position.
Press the MODE button one time to get to the Main Selection
Screen, select Setup. Set Time and Date by pressing ENTER,
using UP/DOWN to adjust selected field, LEFT/RIGHT to move
to the next field and ENTER when done.
Press MODE button until MENU SELECTION screen is
displayed. Use the UP/DOWN buttons until the MAIN
SCREEN option is highlighted yellow. Press ENTER.
Switch camera to
ON
. Your camera will now automatically
take pictures whenever an animal is detected in range,
based on the default settings below.
Capture Mode
MOTION DETECT
Photo Quality
HIGH (4.0 MP)
Photo Delay after each photo is taken
5 SECONDS
Motion Freeze
ON
Multi Shot Count
OFF
Digital Zoom
NONE
Video Resolution
VGA
Video Length
10 SECONDS
Video Audio
ON
Camera Name
MOULTRIECAM
Temperature
FAHRENHEIT
Info Strip printed on photos
ON
Time Lapse Frequency
30 SECONDS
Time Lapse Duration
3 HOUR
GPS Longitude & Latitude:
000.000000 N / 000.000000 E
Delete All?
NO
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 7
Page 3
M-990i Digital Game Camera
PLOTSTALKER ACTIVITY SEARCH
B
Slide the UNLOCK switch on the bottom of Camera and use the knob to pull the
slide-out Battery Tray. Install or eight(8) AA size alkaline or lithium batteries
with polarities as indicated in the Battery Tray. Re-install the Battery Tray.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as shown.
Turn Camera on by sliding ON/OFF/IR TEST switch
to the ON position.
Press the MODE button one time to get to the
Camera Setup Menu. Set Time and Date by pressing
ENTER, using UP/DOWN to adjust selected field,
LEFT/RIGHT to move to the next field and ENTER
when done.
Press MODE button until MENU SELECTION
screen is displayed. Use the UP/DOWN buttons
until the MAIN SCREEN option is highlighted
yellow. Press ENTER.
Your Camera will now automatically take pictures
whenever an animal is detected in range -based on
the default settings below.
Eyelet
Mounting
Strap
M-880 GameSpy Digital Camera
PlotStalker Software
Page 3
Page 14
PLOTSTALKER ACTIVITY SEARCH
B
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .mlt photo file, stops
on a photo when changes are found in your identified region, and then highlights
the changes in blue. You can click anywhere in the video viewing area to remove
the blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
1
2
3
Click on the Set Motion Search Area Button.
Use the mouse to select and drag the red outline around the area you want to
search for movement. This allows you to focus on a very precise area if
required.
Click OK button on the Settings Popup window to confirm your settings and
exit the menu.
Set to High, Medium or Low - This sets the level of pixel change the program
will detect. Note; a pixel change will occur with a color, intensity, lighting or
movement so this setting is critical to obtain the desired results.
1
SENSITIVITY
Click on Default button to return to the default values for Search Area and
Sensitivity settings.
GPS Latitude - 000.000000 N
GPS Longitude - 000.000000 W
1
DEFAULT SETTINGS
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
Capture Mode
TRAIL CAM (Still)
Photo Quality
2.0 MP
Photo Delay after each photo is taken
5 SEC
Motion Freeze
ON
Multi Shot Count
OFF
Video Resolution
VGA
Video Length
5 SEC
Video Audio
ON
Camera Name
MOULTRIECAM
Temperature
FAHRENHEIT
Info Strip printed on photos
ON
Plot Frequency
15 SECONDS
Plot Duration
3 HOUR
GPS Longitude & Latitude:
NO
NO
000.000000 N / 000.000000 W
Delete All?
Default Setting
Security Code
00000
Slide the UNLOCK switch on the bottom of Camera and use the knob to pull the
slide-out Battery Tray. Install or eight(8) AA size alkaline or lithium batteries
with polarities as indicated in the Battery Tray. Re-install the Battery Tray.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as shown.
Turn Camera on by sliding ON/OFF/IR TEST switch
to the ON position.
Press the MODE button one time to get to the
Camera Setup Menu. Set Time and Date by pressing
ENTER, using UP/DOWN to adjust selected field,
LEFT/RIGHT to move to the next field and ENTER
when done.
Press MODE button until MENU SELECTION
screen is displayed. Use the UP/DOWN buttons
until the MAIN SCREEN option is highlighted
yellow. Press ENTER.
Your Camera will now automatically take pictures
whenever an animal is detected in range -based on
the default settings below.
Eyelet
Mounting
Strap
M-880 GameSpy Digital Camera
PlotStalker Software
Page 3
Page 14
PLOTSTALKER ACTIVITY SEARCH
B
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .mlt photo file, stops
on a photo when changes are found in your identified region, and then highlights
the changes in blue. You can click anywhere in the video viewing area to remove
the blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
1
2
3
Click on the Set Motion Search Area Button.
Use the mouse to select and drag the red outline around the area you want to
search for movement. This allows you to focus on a very precise area if
required.
Click OK button on the Settings Popup window to confirm your settings and
exit the menu.
Set to High, Medium or Low - This sets the level of pixel change the program
will detect. Note; a pixel change will occur with a color, intensity, lighting or
movement so this setting is critical to obtain the desired results.
1
SENSITIVITY
Click on Default button to return to the default values for Search Area and
Sensitivity settings.
GPS Latitude - 000.000000 N
GPS Longitude - 000.000000 W
1
DEFAULT SETTINGS
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
Capture Mode
TRAIL CAM (Still)
Photo Quality
2.0 MP
Photo Delay after each photo is taken
5 SEC
Motion Freeze
ON
Multi Shot Count
OFF
Video Resolution
VGA
Video Length
5 SEC
Video Audio
ON
Camera Name
MOULTRIECAM
Temperature
FAHRENHEIT
Info Strip printed on photos
ON
Plot Frequency
15 SECONDS
Plot Duration
3 HOUR
GPS Longitude & Latitude:
NO
NO
000.000000 N / 000.000000 W
Delete All?
Default Setting
Security Code
00000
Slide the UNLOCK switch on the bottom of Camera and use the knob to pull the
slide-out Battery Tray. Install or eight(8) AA size alkaline or lithium batteries
with polarities as indicated in the Battery Tray. Re-install the Battery Tray.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as shown.
Turn Camera on by sliding ON/OFF/IR TEST switch
to the ON position.
Press the MODE button one time to get to the
Camera Setup Menu. Set Time and Date by pressing
ENTER, using UP/DOWN to adjust selected field,
LEFT/RIGHT to move to the next field and ENTER
when done.
Press MODE button until MENU SELECTION
screen is displayed. Use the UP/DOWN buttons
until the MAIN SCREEN option is highlighted
yellow. Press ENTER.
Your Camera will now automatically take pictures
whenever an animal is detected in range -based on
the default settings below.
Eyelet
Mounting
Strap
M-880 GameSpy Digital Camera
PlotStalker Software
Page 3
Page 14
PLOTSTALKER ACTIVITY SEARCH
B
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .mlt photo file, stops
on a photo when changes are found in your identified region, and then highlights
the changes in blue. You can click anywhere in the video viewing area to remove
the blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
1
2
3
Click on the Set Motion Search Area Button.
Use the mouse to select and drag the red outline around the area you want to
search for movement. This allows you to focus on a very precise area if
required.
Click OK button on the Settings Popup window to confirm your settings and
exit the menu.
Set to High, Medium or Low - This sets the level of pixel change the program
will detect. Note; a pixel change will occur with a color, intensity, lighting or
movement so this setting is critical to obtain the desired results.
1
SENSITIVITY
Click on Default button to return to the default values for Search Area and
Sensitivity settings.
GPS Latitude - 000.000000 N
GPS Longitude - 000.000000 W
1
DEFAULT SETTINGS
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
Capture Mode
TRAIL CAM (Still)
Photo Quality
2.0 MP
Photo Delay after each photo is taken
5 SEC
Motion Freeze
ON
Multi Shot Count
OFF
Video Resolution
VGA
Video Length
5 SEC
Video Audio
ON
Camera Name
MOULTRIECAM
Temperature
FAHRENHEIT
Info Strip printed on photos
ON
Plot Frequency
15 SECONDS
Plot Duration
3 HOUR
GPS Longitude & Latitude:
NO
NO
000.000000 N / 000.000000 W
Delete All?
Default Setting
Security Code
00000
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .MLT photo file, stops on a photo when
changes are found in your identified region, and then highlights the changes in blue. You can click
anywhere in the video viewing area to remove the blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
SENSITIVITY
Set to High, Medium or Low - This sets the level of pixel change the program will detect.
Note:
A pixel change occurs when a change in color, intensity, lighting or movement is detected, so
this setting is critical to be able to jump to the desired frames.
DEFAULT SETTINGS
Click on Default button to return to the default values for Search Area and Sensitivity settings.
1. Click on the Set Motion Search Area Button.
2. Use the mouse to select and drag the red outline around the area you want to search for
movement. This allows you to focus on a very precise area if required.
3. Click OK button on the Settings Popup window to confirm your settings and exit the menu.
Page 14
Plot Stalker Software
Switch camera to
Aim
. Aim camera using motion
detection to determine target area. Walk in front of the
camera at the desired distance and the camera LED will
flash showing the covered area.
STEP 6
