background image

GV20401a_e.doc / Sep-08 

 

Page 3 / 10 

 

Table of Contents 

 

 

1.

 

Compatibility Hint ...........................................................................................4

 

2.

 

Application ......................................................................................................5

 

3.

 

Block Diagram .................................................................................................5

 

4.

 

Power Supply ..................................................................................................6

 

4.1.

 

Supply from an unstabilized 10 - 30 volts DC source 

6

 

4.2.

 

Supply from a stab5 volts DC source 

6

 

5.

 

Impulse Inputs.................................................................................................7

 

6.

 

Impulse Outputs and Output Levels ................................................................8

 

7.

 

Dimensions......................................................................................................9

 

8.

 

Specifications................................................................................................10

 

 

Summary of Contents for GV204











Reviews: