Motorola VX-P949 User Manual Download

Page: 74 / 112

6.12.1

Enabling or Disabling Radio Lock (Secure Radios Only)

Procedure:

or to

Logf

Press the

Menu Select

button directly below

Logf

One of the following results occur:

• The display shows

Pswd enabled

, indicating that the radio lock feature is enabled.

• The display shows

Pswd disabled

, indicating that the radio lock feature is disabled.

6.12.2

Changing the Radio Lock Password

Procedure:

or to

Pswd

Press the

Menu Select

button directly below

Pswd

The display shows

Change Password

screen.

Unlock Pswd

Press the

Menu Select

button directly below

Sel

Enter the old password.

Press the

Menu Select

button directly below

Enter the new password.

Press the

Menu Select

button directly below

Re-enter the new password.

Press the

Menu Select

button directly below

The password is updated.

If the two passwords do not match, repeat

step 5

through

step 10

NOTICE:

If you enter three incorrect old passwords, the radio exits the password feature. You

cannot access this feature again until you turn the radio off and on.

6.12.3

Changing the Tactical Inhibit Password

The Tactical Inhibit Password is required for the Radio Stun and Radio Kill features. You can set up to
eight characters for this password.

Procedure:

or to

Pswd

Press the

Menu Select

button directly below

Pswd

The display shows

Change Password

screen.

Tactical Inh Encode Pswd

MN003602A01-AF
Advanced Features

Summary of Contents for VX-P949
















































































































Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands

Motorola VX-P949, User Manual

Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands